00324867

Centraline EnOcean Easyclick Temperature Actuator

Easyclick wireless radio valve actuator with integrated EnOcean radio interface for bidirectional communication with control and regulation units.
The actuator has an integrated temperature sensor and can be used for actuator operation.
The power supply is provided by three alkaline AA batteries. A high-quality mechanics and an intelligent control method ensure a battery life of up to 3 years.
Daily status reports as well as visual and acoustic signals indicate insufficient battery capacity.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.
Model: Wireless radio valve actuator (D 451 FU-E MSA2) (thermokon SAB05)


00331616

Centraline EnOcean Wall modules, Temperature

Room operating unit (with set point adjuster) and EnOcean radio interface for manual operation of HVAC applications and temperature measurement in living rooms, offices, warehouses, etc., without batteries and maintenance-free surface mounting. The energy is generated via the integrated solar cell. Excess energy is stored in the internal energy buffer. The measured values are transmitted at predefined intervals. The intervals can be adjusted via jumpers on the device.
The sensor can be glued directly to surfaces for easy installation.
For mounting at positions with low brightness, a battery inside the device can be used as an option.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Room temperature sensor (SR04)


00331626

Centraline EnOcean Wall modules, Temperature

Room operating unit (with set point adjuster) and EnOcean radio interface for manual operation of HVAC applications and temperature measurement in living rooms, offices, warehouses, etc., without batteries and maintenance-free surface mounting. The energy is generated via the integrated solar cell. Excess energy is stored in the internal energy buffer. The measured values are transmitted at predefined intervals. The intervals can be adjusted via jumpers on the device.
The sensor can be glued directly to surfaces for easy installation.
For mounting at positions with low brightness, a battery inside the device can be used as an option.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Room temperature sensor with set point adjuster (SR04P)


00331666

Centraline EnOcean Wall module, Temperature and Relative Humidity

Room sensor with EnOcean wireless interface for measuring temperature and humidity in living rooms, offices, warehouses, etc. The energy is generated via the integrated solar cell. Excess energy is stored in the internal energy buffer. The measured values are transmitted at predefined intervals.
The intervals can be adjusted via jumpers on the device. The sensor can be glued directly to surfaces for easy installation. For mounting at positions with low brightness, a battery inside the device can be used as an option.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.
Model: Room temperature/ R.H. sensor (SR04 RH)


00331686

Centraline EnOcean Wall module, Temperature and CO2

Surface-mounted air quality sensor with EnOcean radio interface for measuring the CO2 content and temperature in living rooms, offices, warehouses, etc. The CO2 measurement is carried out by means of 'Non-Dispersive InfraRed (NDIR)' technology with automatic self-calibration (Dual Channel).
The measured values are transmitted at predefined intervals. The intervals can be adjusted via jumpers on the device. For prewiring at the installation site, the lower part of the housing with terminal clamp can be removed from the upper part of the housing.
Offset values can be calibrated directly on the device via potentiometers.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.
Model: Room temperature/CO2 sensor (SR04 CO2)


00364356

Centraline EnOcean Easyclickpro Blind Actuators

The Easyclickpro actuators use Enocean technology (868MHz) with integrated energy measurement.
For roller shutters and blinds, not only receives the radio signals but also sends back its status with every change of state.
Bidirectional Easyclickpro components can then be automatically recognized by the controller and integrated into the controller program via a simple drag-and-drop operation.
The controller program has access to all functions of the Easyclickpro components, so that, for example, blinds can be controlled centrally with precise positioning or energy consumption values can be recorded.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Flush mounting roller/shutter receiver, bidirectional, 2-channel (D 452 FU-EBI JR o.T.)


00364576

Centraline EnOcean Easyclickpro Switch Actuators

The Easyclickpro switches use Enocean technology (868MHz) with integrated energy measurement.
For light circuits additionally offers the recording of energy consumption, current power consumption, operating hours or lamp faults of the connected load. This means that the building control system can not only record energy consumption without having to install additional meters, it also enables proactive service, for example by allowing lamps to be replaced preventively at the end of their service life.
Bidirectional Easyclickpro components can then be automatically recognized by the controller and integrated into the controller program via a simple drag-and-drop operation.
The controller program has access to all functions of the Easyclickpro components, so that, for example, blinds can be controlled centrally with precise positioning or energy consumption values can be recorded.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Plug through switch, bidirectional, 1-channel with energy meter (SCHUKO) (D 4511 FU-EBIM ST)


00364936

Centraline EnOcean Accessories, Handheld transmitter

The EnOcean Easyclick comfort hand-held transmitter is absolutely necessary as a service tool for commissioning the Easyclickpro flush-mounted receiver with a Hawk or Eaglehawk controller. With the hand transmitter, each receiver is given an individual code by means of which the receiver can be addressed by the controller at any time.
The communication protocol between Centraline controllers and the aerial module gateway is defined in a special software driver what is available for the Arena AX software.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.
Model: Comfort hendheld transmitter, 128 channel (D 450 FU-HS128)


00366536

Centraline EnOcean Easyclickpro Switch Actuators

The Easyclickpro switches use Enocean technology (868MHz) with integrated energy measurement.
For light circuits additionally offers the recording of energy consumption, current power consumption, operating hours or lamp faults of the connected load. This means that the building control system can not only record energy consumption without having to install additional meters, it also enables proactive service, for example by allowing lamps to be replaced preventively at the end of their service life.
Bidirectional Easyclickpro components can then be automatically recognized by the controller and integrated into the controller program via a simple drag-and-drop operation.
The controller program has access to all functions of the Easyclickpro components, so that, for example, blinds can be controlled centrally with precise positioning or energy consumption values can be recorded.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Flush mounting receiver, bidirectional, 1-channel with energy meter (D 451 FU-EBIM o.T.)


00366556

Centraline EnOcean Easyclickpro Switch Actuators

The Easyclickpro switches use Enocean technology (868MHz) with integrated energy measurement.
For light circuits additionally offers the recording of energy consumption, current power consumption, operating hours or lamp faults of the connected load. This means that the building control system can not only record energy consumption without having to install additional meters, it also enables proactive service, for example by allowing lamps to be replaced preventively at the end of their service life.
Bidirectional Easyclickpro components can then be automatically recognized by the controller and integrated into the controller program via a simple drag-and-drop operation.
The controller program has access to all functions of the Easyclickpro components, so that, for example, blinds can be controlled centrally with precise positioning or energy consumption values can be recorded.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Flush mounting receiver, bidirectional, 2-channel with energy meter (D 452 FU-EBIM o.T)


00366576

Centraline EnOcean Easyclickpro Blind Actuators

The Easyclickpro actuators use Enocean technology (868MHz) with integrated energy measurement.
For roller shutters and blinds, not only receives the radio signals but also sends back its status with every change of state.
Bidirectional Easyclickpro components can then be automatically recognized by the controller and integrated into the controller program via a simple drag-and-drop operation.
The controller program has access to all functions of the Easyclickpro components, so that, for example, blinds can be controlled centrally with precise positioning or energy consumption values can be recorded.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.


Model: Flush mounting roller/shutter receiver, bidirectional, 2-channel with position detection (D 452 FU-EBIM JR o.T.)


00367113

Centraline EnOcean Easyclick Design window contact

Easyclick Batteryless radio window/door contact for monitoring window and door statuses with Easyclick radio signals sent to Hawk- or Eaglehawk-controllers.
The Easyclick window contact is wireless and perfectly maintenance free with internal solar powered energy storage. It can operate for several days in the dark. Immediate signal transmission when a window is opened or closed, triggered by a window magnet.
The integration into the CentraLine system takes place via bus-capable antennas D 450 ANT AX which can be distributed in the building. The antenna bus is optionally connected to the HAWK or EAGLEHAWK controller.
Model: Window contact (D 450 FU-FK)


00377806

Centraline EnOcean Accessories, Aerial module

The aerial module is part of the PEHA Easyclick system. The aerial module was developed as a gateway between the PEHA Easyclick EnOcean products and the Centraline HAWK/EAGLEHAWK controllers.
The communication protocol between Centraline controllers and the aerial module gateway is defined in a special software driver what is available for the Arena AX software.
The signals are transmitted over the European harmonized frequency 868.3 MHz.
Model: Aerial module (D 450 ANT AX)


075041061

Centraline Compact Line Rotary Actuator


Linkage of M6063L as replacement for M676A,C



0903403

Centraline Three-way control valve PN16, threaded connections DN15-50, V5078B


Adapter ring



43161276-001

Centraline Pneumatic actuator, MP953
High Temperature Applications, the following bonnet extentions must be used with MP953 actuators when the flowing medium temperature is 150 to 220 degrees C, to give extra air circulation and less conduction of heat from the valve body to the actuator.

Used with V5049A up to 65mm, V5050A up to 80mm, V5328A 40mm to 80mm, V5329A 40mm to 80mm



43191679-001

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories

Single feedback potentiometer 220/135 ohm operating range, for 20 mm models



43191679-002

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories

Single feedback potentiometer 220/135 ohm operating range, for 38 mm models



43191679-007

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories

Single feedback potentiometer 10 kohm operating range, for 20 mm models



43191679-008

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories

Single feedback potentiometer 10 kohm operating range, for 38 mm models



43191679-011

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Accessories

Feedback potentiometer 10 kohm, operating range



43191679-012

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Accessories

Feedback potentiometer 220 ohm operating range



43191680-002

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421
Accessories

Dual end switches SPDT, adjustable (250 V~, 10 A)



43191680-005

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
Accessories

Dual end switches SPDT, adjustable (250 V~, 10 A)



43191680-205

Centraline Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425
Accessories

Auxiliary switch (250 V~, 10 A)



43196000-001

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
High temperature kits for:

V5011R/S, V5013R/E; V5328A/V5329A DN15..32



43196000-002

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425
High temperature kits for:

V5016A/V5025A/V5050A DN15..80; V5049A DN15..65; V5095A DN20..80; V5328A/V5329A DN40..80



43196000-038

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421
High temperature kits for:

V5015A/V5016A/V5025A/V5049A/V5050A/B/V5328A 38 mm



5112-11/U

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Linkage set for Damper actuators

Linkage set for VBG valves; DN15-32 for usage with S03.. actuators; DN15-50 for usage with N05.., S05.. actuators



5112-19/U

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves

Replacement stem assembly for VBG valve, DN15, DN20



5112-20/U

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves

Replacement stem assembly for VBG valve, DN25, DN32



5112-21/U

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN40, DN50 valves

Replacement stem assembly for VBG valve, DN40, DN50



5112-51/U

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN40, DN50 valves

Linkage set for VBG valves DN40, DN50 to M6061, M7061



5585100

Centraline Two-way control valve PN16, conical sealing DN15/20, V5822A
Accessories

Spare adjustment cap (pack of 10)



AC-15FS

Centraline Valve Small, Flat sealing, 2-way, PN16, DN15/20/25, VSxF-2
Accessories

Soldering fitting for DN15 valve, pipe size 12 mm



AC-15FT

Centraline Valve Small, Flat sealing, 2-way, PN16, DN15/20/25, VSxF-2
Accessories

External threaded fitting for DN15 valve, pipe size R3/8"



AC-15TF

Centraline Three-way control valve PN16, flat sealing DN15-50, V5013E
Accessories

Internal threaded fitting for DN15 valve, pipe size Rp1/2"



AC-15TF-1

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves

Internal threaded fitting for VBG DN15 valve, pipe size Rp 1/2"



AC-20FS

Centraline Valve Small, Flat sealing, 2-way, PN16, DN15/20/25, VSxF-2
Accessories

Soldering fitting for DN20 valve, pipe size 15 mm



AC-20FT

Centraline Valve Small, Flat sealing, 2-way, PN16, DN15/20/25, VSxF-2
Accessories

External threaded fitting for DN20 valve, pipe size R1/2"



AC-20TF

Centraline Three-way control valve PN16, flat sealing DN15-50, V5013E
Accessories

Internal threaded fitting for DN20 valve, pipe size Rp3/4"



AC-25T

Centraline Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories

External threaded fitting for DN25 valve, pipe size R1"



AC-25TF

Centraline Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories

Internal threaded fitting for DN25 valve, pipe size Rp1"



AC-32T

Centraline Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories

External threaded fitting for DN32 valve, pipe size R11/4"



AC-32TF

Centraline Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories

Internal threaded fitting for DN32 valve, pipe size Rp11/4"



AC-40T

Centraline Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories

External threaded fitting for DN40 valve, pipe size R11/2"



AC-40TF

Centraline Two-way control valve PN16, flat sealing DN25-40, V5832B
Accessories

Internal threaded fitting for DN40 valve, pipe size Rp11/2"



AC-50TF

Centraline Three-way control valve PN16, flat sealing DN15-50, V5013E
Accessories

Internal threaded fitting for DN50 valve, pipe size Rp2"



ACN-15C

Centraline Valve Small, Conical sealing, 2-way, PN16, DN15/20/25, VSxC-2
Accessories

Compression fitting for DN15 valve, pipe size 15 mm



ACN-15S

Centraline Valve Small, Conical sealing, 2-way, PN16, DN15/20/25, VSxC-2
Accessories

Soldering fitting for DN15 valve, pipe size 12 mm



ACN-15T

Centraline Valve Small, Conical sealing, 2-way, PN16, DN15/20/25, VSxC-2
Accessories

External threaded fitting for DN15 valve, pipe size R3/8"



ACN-20C

Centraline Valve Small, Conical sealing, 2-way, PN16, DN15/20/25, VSxC-2
Accessories

Compression fitting for DN20 valve, pipe size 22 mm



ACN-20S

Centraline Valve Small, Conical sealing, 2-way, PN16, DN15/20/25, VSxC-2
Accessories

Soldering fitting for DN20 valve, pipe size 15 mm



ACN-20T

Centraline Valve Small, Conical sealing, 2-way, PN16, DN15/20/25, VSxC-2
Accessories

External threaded fitting for DN20 valve, pipe size R1/2"



ACS-25T

Centraline Valve Small, Flat sealing, 2-way, PN16, DN15/20/25, VSxF-2
Accessories

External threaded fitting for DN25 valve, pipe size R1"



AF00-B54

Centraline Outdoor temperature sensor, Pt1000

Approvals: IEC751 class B
Temperature element: Pt1000
Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Protection class: IP54


AF00-B65

Centraline Outdoor temperature sensor, Pt1000

Approvals: IEC751 class B
Temperature element: Pt1000
Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Protection class: IP65


AF10-B54

Centraline Outdoor temperature sensor, NTC

Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Temperature element: NTC10k
Protection class: IP54
Comment: no


AF10-B65

Centraline Outdoor temperature sensor, NTC

Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Temperature element: NTC10k
Protection class: IP65
Comment: no


AF20-B54

Centraline Outdoor temperature sensor, NTC

Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Temperature element: NTC20k
Protection class: IP54
Comment: no


AF20-B65

Centraline Outdoor temperature sensor, NTC

Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Temperature element: NTC20k
Protection class: IP65
Comment: no


AF20-B65-N

Centraline Outdoor temperature sensor, NTC

Temperature range: -40...70C
Mounting place: wall outside
Housing (HxWxD): 56mm|81mm|49mm
Wiring terminals: 2


Temperature element: NTC20k
Protection class: IP65
Comment: no logo


AKA3

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Accessories for models with boiler burner output

Cable accessory



AS2

Centraline Actuator for V5421B1090
Optional accessories

End switch



ATU2040A

Centraline Rotary Actuator
Mounting kit for non-Honeywell valves

Universal kit for almost all valves



BACA-A

Centraline Configurable BACnet room controller MERLIN
Tools for Commissioning

Wireless Adapter



C7110A1010

Centraline Air quality sensor

For detection of unpleasant odours, tobacco smoke, and vapours emitted by such materials as furniture, carpets, paint, glue, etc.
Protection class: III as per EN60730-1I IP30 as per EN60529
Output signal: 0..10Vdc
Adjustable output offset and LED display
Power supply: 24Vacdc
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


C7110C1001A

Centraline Room temperature/ CO2 sensor

For sensing or controlling of CO2 concentration in buildings.
LED functions: operation as CO2 indicator
Output signal: CO2: 0..10 V for 0..2000 ppm (factory setting) or 0..3000 ppm
temperature: 0..10 V
Automatic baseline calibration, and quick calibration options.
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


C7110D1009A

Centraline Room temperature/ CO2 sensor

For sensing or controlling of CO2 concentration; and temperature measurement in buildings.
LED functions: operation as occupancy indicator
Output signal: CO2: 0..10 V for 0..2000 ppm (factory setting) or 0..3000 ppm
Temperature setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.
Automatic baseline calibration, and quick calibration options.
Temperature element: NTC20k
Temperature range: 10...35C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


CABLE-CONTROL

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Control Spares
Product description: Set of linking cable for HVAC400 older than March 2018
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


CL-ROOMUP

Centraline Configurable BACnet room controller MERLIN
Tools for Commissioning

Mobile Commissioning Tool



CLAXARENAAXI

Centraline Web based Supervisor software, ARENA AX
CL AX Video Drivers

Axis Cameras video driver 16 Cameras



CLAXARENAAXI4

Centraline Web based Supervisor software, ARENA AX
CL AX Video Drivers

Additional 4 Cameras Axis video driver



CLAXARENADED

Centraline Web based Supervisor software, ARENA AX
CL AX Video Drivers

Dedicated Micros NetVu DVR video driver 16 Cameras



CLAXARENAMIL

Centraline Web based Supervisor software, ARENA AX
CL AX Video Drivers

Milestone NVM video driver 16 Cameras



CLAXARENAMIL4

Centraline Web based Supervisor software, ARENA AX
CL AX Video Drivers

Additional 4 Cameras Milestone NVM video driver



CLAXARENASBSU1

Centraline Web based Supervisor software, ARENA AX
CL ARENA AX Upgrades

Upgrade CLAXARENASBS01 Small Building Supervisor 1 additional HAWK



CLAXARENASBSU5B

Centraline Web based Supervisor software, ARENA AX
CL ARENA AX Upgrades

upgrade SBS05 to SBS10



CLAXARENASBSUP

Centraline Web based Supervisor software, ARENA AX
CL ARENA AX Upgrades

Upgrade of ARENA AX Small Building Supervisor to full ARENA AX



CLAXARENASMS

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

SMS Driver for ARENA AX



CLAXDBCSV

Centraline Web based Supervisor software, ARENA AX
CL AX Database Drivers

Database, CSV Server Driver



CLAXDBMYSQL

Centraline Web based Supervisor software, ARENA AX
CL AX Database Drivers

Database, MySQL Driver



CLAXDBSQL

Centraline Web based Supervisor software, ARENA AX
CL AX Database Drivers

Database, MS SQL Server Driver



CLAXDBTBL

Centraline Web based Supervisor software, ARENA AX
CL AX Database Drivers

Database, Table Driver



CLAXDRBAC500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 BACnet points



CLAXDRBACAWS

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional BACnet AWS feature for ARENA AX



CLAXDRBACEXP

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional BACnet Server Export feature for ARENA AX



CLAXDRBACOWS

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

BACnet IP Driver, OWS certified, with 500 BACnet points



CLAXDRCBUS

Centraline Web based Supervisor software, ARENA AX
C-Bus drivers

AX C-BUS DRIVER UNLIMITED POINTS



CLAXDRCBUS500

Centraline Web based Supervisor software, ARENA AX
C-Bus drivers

AX C-BUS DRIVER LIMITED TO 500 POINTS



CLAXDRCBUSUP

Centraline Web based Supervisor software, ARENA AX
C-Bus drivers

AX C-BUS DRIVER UPGR TO UNLIMITED POINTS



CLAXDREIB

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

EIB IP Driver with 500 EIB points



CLAXDREIB500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 EIB points



CLAXDRFIDELIO

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Fidelio Hotel booking system driver



CLAXDRLONIP

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

LON IP Driver with 500 LON points



CLAXDRLONIP500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 LON points



CLAXDRMBSIP

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

MBus IP Driver with 500 points



CLAXDRMBSIP500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 MBus IP points



CLAXDRMTCP

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Modbus TCP Driver with 500 Modbus TCP points



CLAXDRMTCP500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 Modbus TCP points



CLAXDROBX

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

OBIX Driver for non-Niagara point connectivity with 500 OBIX points



CLAXDROBX500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 OBIX points



CLAXDROPC

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

OPC Driver with 500 OPC points



CLAXDROPC500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 OPC points



CLAXDROPE

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

OPC Client alarm and event notification driver with 500 points



CLAXDROPE500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 points for OPC alarm and event notification driver



CLAXDRSNMP

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

SNMP Driver with 500 SNMP points



CLAXDRSNMP500

Centraline Web based Supervisor software, ARENA AX
CL AX ARENA open system Drivers

Additional 500 SNMP points



CLAXEH00ND100A

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: EAGLEHAWK controller including base license; 102 Panel-Bus points; 5 integrated devices, 25 integrated points


CLAXEH14ND100A

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: EAGLEHAWK controller with 14 onboard IO, including base license; 102 Panel-Bus / Onboard IO points; 5 integrated devices, 25 integrated points


CLAXEH26ND100A

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: EAGLEHAWK controller with 26 onboard IO, including base license; 102 Panel-Bus / Onboard IO points; 5 integrated devices, 25 integrated points


CLAXEH3PTY25UP

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: Additional 25 integrated points, 5 integrated devices


CLAXEHPB100UP

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: Additional 100 Panel-Bus points


CLAXEHRBAC150UP

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: 150 BACnet room integration points for Honeywell room controllers


CLAXEHRLON150UP

Centraline EAGLEHAWK Integrated Plant Control

BACnet-compliant heating, ventilation, air conditioning Building Controller. It runs the CentraLine Niagara framework, integrating all trades in a building.
Control software: Freely programmable with CentraLine COACH AX software
utilizes the CentraLine HVAC application library for maximum energy efficiency
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA AX
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
FOX/IP and FOXS/IP (Secure FOX) communication with ARENA AX and other Niagara devices as HAWK
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces
Panel-bus for communication to Panel I/O modules via one or both onboard RS485 interfaces
LonWorks(R) bus with the external USB-LON interface adapter IF-LON. LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus RTU via one or both onboard RS485 interfaces Modbus TCP communication via the onboard Ethernet RJ45 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers
In addition to the protocols above, also other network drivers which are available within the Niagara system can be used with the EAGLEHAWK e.g. KNX via the onboard Ethernet interface
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing

Controller
Product description: 150 LON room integration points for Honeywell room controllers


CLCH3EL4

Centraline HVAC controller with configurable applications, PANTHER
COACH for selection of control software, downloadable from CentraLine partner web

COACH for Expert Partner



CLCM1C155A

Centraline CentraLine room temperature/ CO2 sensor

For sensing or controlling of CO2 concentration; and temperature measurement in buildings.
Protection class: IP30
Output signal: the following CO2 output signals are applicable, analog or digital
0..10V for 0..2000 ppm (factory setting)
0..10 V or 2..10 V for 0..2000 ppm or 0..3000 ppm (configurable)
Temperature element: NTC20k
Power supply: 24Vacdc
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm
Wiring terminals: 3
LED functions: CO2 indicator


CLCM1H112

Centraline CentraLine room temperature/R.H. sensor

Protection class: IP30
central override of setpoint
Temperature element: NTC20k
Temperature range: 6...40C
R.H. range: 20...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vacdc
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm
Wiring terminals: 4


CLCM1T11N

Centraline CentraLine room temperature sensors

Protection class: IP30
Temperature element: NTC20k
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


Temperature range: 6...40C
Setpoint knob: no
Extra setp. knob: no
Occupancy switch: no
Fan switch: no
Wiring terminals: 2
LED functions: no
Note: no


CLCM2T11N

Centraline CentraLine room temperature sensors

Protection class: IP30
Temperature element: NTC20k
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


Temperature range: 6...40C
Setpoint knob: -5...5K
Extra setp. knob: 12...30C
Occupancy switch: no
Fan switch: no
Wiring terminals: 3
LED functions: no
Note: no


CLCM3T111

Centraline CentraLine room temperature sensors

Protection class: IP30
Temperature element: NTC20k
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


Temperature range: -15...40C
Setpoint knob: -7...7K
Extra setp. knob: no
Occupancy switch: auto/off/on
Fan switch: no
Wiring terminals: 5
LED functions: error indication
Note: not for SERVAL


CLCM4T111

Centraline CentraLine room temperature sensors

Protection class: IP30
Temperature element: NTC20k
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


Temperature range: 6...40C
Setpoint knob: -5...5K
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Fan switch: no
Wiring terminals: 7
LED functions: no
Note: no


CLCM5T111

Centraline CentraLine room temperature sensors

Protection class: IP30
Temperature element: NTC20k
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


Temperature range: 6...40C
Setpoint knob: -5...5K
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Fan switch: auto/off/on
Wiring terminals: 7
LED functions: no
Note: no


CLCM6H212

Centraline CentraLine room temperature/R.H. sensor, with display

Room temperature sensor with digital display. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status, humidity
Protection class: IP30
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
central override of setpoint and fan speed
Temperature element: NTC20k
Temperature range: 6...40C
Setpoint knob: -5...5K
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: auto/off/1/2/3
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


R.H. range: 10/15/20...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Wiring terminals: 8


CLCM6T111

Centraline CentraLine room temperature sensors

Protection class: IP30
Temperature element: NTC20k
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


Temperature range: 6...40C
Setpoint knob: -5...5K
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Fan switch: auto/off/1/2/3
Wiring terminals: 7
LED functions: no
Note: no


CLCM6T21N

Centraline CentraLine room temperature/R.H. sensor, with display

Room temperature sensor with digital display. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status, humidity
Protection class: IP30
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
central override of setpoint and fan speed
Temperature element: NTC20k
Temperature range: 6...40C
Setpoint knob: -5...5K
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: auto/off/1/2/3
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm


R.H. range: no
R.H. sensing element: no
R.H. output signal: no
Wiring terminals: 7


CLCMNA172B

Centraline CentraLine air quality sensor

For detection of unpleasant odours, tobacco smoke, and vapours emitted by such materials as furniture, carpets, paint, glue, etc.
Protection class: IP30
Output signal: 0..10Vdc
Adjustable output offset.
Power supply: 24Vacdc
Mounting place: internal wall
Housing (HxWxD): 104mm|104mm|33mm
LED functions: air quality indication


CLCMTR40

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, no display

Lynx wall module with temperature, no display



CLCMTR40-C02

Centraline Freely programmable BACnet room controller, LYNX
Configurable wall modules, no display

Lynx wall module with temperature + CO2, no display



CLCMTR40-CO2

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, no display

Lynx wall module with temperature + CO2, no display



CLCMTR40-H

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, no display

Lynx wall module with temperature + humidity, no display



CLCMTR40-H-CO2

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, no display

Lynx wall module with temperature + hum. + CO2, no display



CLCMTR42

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, with display

Lynx wall module with temperature, with display



CLCMTR42-CO2

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, with display

Lynx wall module with temperature + CO2, with display



CLCMTR42-H

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, with display

Lynx wall module with temperature + humidity, with display



CLCMTR42-H-CO2

Centraline Configurable BACnet room controller MERLIN
Configurable wall modules, with display

Lynx wall module with temperature + hum. + CO2, with display



CLCMTR71

Centraline Freely programmable BACnet room controller, LYNX
Configurable wall modules, with display

Lynx wall module with room temperature sensor and backlit display



CLCMTR71-H

Centraline Freely programmable BACnet room controller, LYNX
Configurable wall modules, with display

Lynx wall module with room temperature and humidity sensor, and backlit display



CLCMTR75

Centraline Freely programmable BACnet room controller, LYNX
Configurable wall modules, with display

Lynx wall module with room temperature sensor and backlit display, LYNX schedule support



CLCMTR75-H

Centraline Freely programmable BACnet room controller, LYNX
Configurable wall modules, with display

Lynx wall module with room temperature and humidity sensor, and backlit display LYNX schedule support



CLEA2000B21

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: no onboard IOs, 600 IOs, with built in HMI


CLEA2000B31

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: no onboard IOs, 600 IOs, with RJ45 socket for external HMI


CLEA2014B21

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: 14 onboard IOs, 52 IOs, with built in HMI, without Ethernet


CLEA2014B22

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: 14 onboard IOs, 52 IOs, with built in HMI


CLEA2014B31

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: 14 onboard IOs, 52 IOs, with RJ45 socket for external HMI, without Ethernet


CLEA2014B32

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: 14 onboard IOs, 52 IOs, with RJ45 socket for external HMI


CLEA2026B21

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: 26 onboard IOs, 600 IOs, with built in HMI


CLEA2026B31

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

BACnet IP and MS /TP controller
Product description: 26 onboard IOs, 600 IOs, with RJ45 socket for external HMI


CLEAHMI-BASE

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

External HMI. Mounting in cabinet front door, or with CLEAHMI-BASE: on wall/metal surface or used as handheld. Connection with Ethernet cable, max. 5m
Product description: Wall-mounting subbase for external HMI; including magnets for magnet mounting and including back cover for handheld


CLEAHMI21

Centraline Programmable universal BACnet Building Controller, EAGLE

BACnet DDC controller for all HVAC control applications, and building automation functionalities. The controller is BTL and AMEV AS-A certified, and can be applied for stand-alone operation, and in networked systems.
For all buildings.
Control software: free programmable with CentraLine CARE software
programmable with standard software modules
Hardware inputs: Onboard inputs and external input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Onboard outputs or external output modules available for:
control devices like servomotors
switching devices like pumps, ventilators
Operator panels: Optional onboard or external HMI, with local language operation and plant-specific operation via configurable fast-access-lists
Standard notebook, laptop, touch-panel, PC for full functional operation via Internet Browser. These panels can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, trending, plant graphics, etc. Access options are USB port or Ethernet.
Touch-panel (5.7") CLMMI00N31 for full functional operation via Internet Explorer (WIN CE); this touch panel can be used for adjustment of set-points, alarm limits, fixing in/outputs, override functions, etc.
Management applications: ARENA AX
Stand-alone operation: yes
Bus system description: Standard BACnet/IP communication with other BACnet controllers and BACnet Front-Ends
Standard BACnet MS/TP communication with other BACnet MS/TP devices via one or both onboard RS485 interfaces.
Panel bus for communication to Panel I/O modules via one or both onboard RS485 interfaces.
LonWorks(R) bus with the external USB-LON interface adapter IF-LON2, LonWorks(R) transceiver type FTT10A
M-Bus(R) via the onboard RS232 interface plus external M-Bus power supply adaptor (e.g. PW3, PW20, PW60)
Modbus(R) RTU Master via one onboard RS485 interface
HTTP and HTTPS (secure HTTP) communication with webbrowsers.
Mounting: in cabinets
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in cabinet front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60 from Relay, for M-Bus interface

External HMI. Mounting in cabinet front door, or with CLEAHMI-BASE: on wall/metal surface or used as handheld. Connection with Ethernet cable, max. 5m
Product description: Optional external HMI, with local language operation and plant-specific operation via configurable fast-access-lists


CLIF-CBUSLC

Centraline C-Bus interfaces

C-Bus Interfaces


Product description: C-Bus to TCP/IP adapter for one physical C-bus and one C-Bus via Lon. For connecting a C-Bus via Lon the device needs the LON-USB interface IF-LON2.


CLIOL821A

Centraline LON I/O modules

LON I/O modules for CentraLine controllers.
cabinet, DIN-rail, fuse box, or wall mounting
override switches and potentiometer operation
LED functions configurable
safety positions configurable
fixed terminals
power supply 24 Vac
short-circuit protected

LON I/O modules
Product description: 8 analog input module NTC10k, NTC20k, Ni1000TK5000, Pt1000, Pt3000, Balco500, contact


CLIOL821A-BLK20

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

20x CLIOL821A and 20x XS821-22



CLIOL822A

Centraline LON I/O modules

LON I/O modules for CentraLine controllers.
cabinet, DIN-rail, fuse box, or wall mounting
override switches and potentiometer operation
LED functions configurable
safety positions configurable
fixed terminals
power supply 24 Vac
short-circuit protected

LON I/O modules
Product description: 8 analog output module 0..10Vdc, 3-pt, binary 0/10V


CLIOL822A-BLK10

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

10x CLIOL822A and 10x XS821-22



CLIOL823A

Centraline LON I/O modules

LON I/O modules for CentraLine controllers.
cabinet, DIN-rail, fuse box, or wall mounting
override switches and potentiometer operation
LED functions configurable
safety positions configurable
fixed terminals
power supply 24 Vac
short-circuit protected

LON I/O modules
Product description: 12 binary input module for contact or totalizer contact 20 Hz


CLIOL823A-BLK20

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

20x CLIOL823A and 20x XS823



CLIOL824A

Centraline LON I/O modules

LON I/O modules for CentraLine controllers.
cabinet, DIN-rail, fuse box, or wall mounting
override switches and potentiometer operation
LED functions configurable
safety positions configurable
fixed terminals
power supply 24 Vac
short-circuit protected

LON I/O modules
Product description: 6 relay output module SPDT 250V, 2(1) A, feedback


CLIOL824A-BLK10

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

10x CLIOL824A and 10x XS824-25



CLIOLR822A

Centraline LON I/O modules

LON I/O modules for CentraLine controllers.
cabinet, DIN-rail, fuse box, or wall mounting
override switches and potentiometer operation
LED functions configurable
safety positions configurable
fixed terminals
power supply 24 Vac
short-circuit protected

LON I/O modules
Product description: 8 analog output module 0..10Vdc, 3-pt, binary 0/10V; with override potentiometer


CLIOLR822A-BLK10

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

10x CLIOLR822A and 10x XS821-22



CLIOLR824A

Centraline LON I/O modules

LON I/O modules for CentraLine controllers.
cabinet, DIN-rail, fuse box, or wall mounting
override switches and potentiometer operation
LED functions configurable
safety positions configurable
fixed terminals
power supply 24 Vac
short-circuit protected

LON I/O modules
Product description: 6 relay output module SPDT 250V, 2(1) A, feedback; with override switch


CLIOLR824A-BLK10

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

10x CLIOLR824A and 10x XS824-25



CLIOP821A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 8 analog input module NTC10k, NTC20k, Ni1000TK5000, Pt1000, Pt3000, Balco500, contact


CLIOP821A-BLK20

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Bulk packages
Product description: 20x CLIOP821A and 20x XS821-22


CLIOP822A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 8 analog output module 0..10Vdc, 3-pt, binary 0/10V


CLIOP823A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 12 binary input module for contact or totalizer contact 20 Hz


CLIOP823A-BLK20

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Bulk packages
Product description: 20x CLIOP823A and 20x XS823


CLIOP824A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 6 relay output module SPDT 250V, 2(1) A, feedback


CLIOP830A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Panel Mixed I/O modules, 8 AI NTC20k, 8 AO 0..10Vdc, 12 binary 15Hz, 6 relays 24V 0,5A
Product description: Mixed I/O module with push-in terminals


CLIOP830A-BLK10

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Bulk packages
Product description: 10x CLIOP830A


CLIOP831A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Panel Mixed I/O modules, 8 AI NTC20k, 8 AO 0..10Vdc, 12 binary 15Hz, 6 relays 24V 0,5A
Product description: Mixed I/O module with screw terminals


CLIOP831A-BLK10

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Bulk packages
Product description: 10x CLIOP831A


CLIOPR822A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 8 analog output module 0..10Vdc, 3-pt, binary 0/10V; with override potentiometer


CLIOPR822A-BLK10

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

Bulk packages
Product description: 10x CLIOPR822A and 10x XS821-22


CLIOPR824A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 6 relay output module SPDT 250V, 2(1) A, feedback; with override switch


CLIOPR824A-BLK10

Centraline EAGLEHAWK Integrated Plant Control
Bulk packages

10x CLIOLR824A and 10x XS824-25



CLIOPR825A

Centraline Panel-Bus IOs

PANEL I/O modules, -configurable LED functions, -safety positions, -short circuit protection

PANEL I/O modules, -configurable LED functions, - safety positions, - short circuit protection
Product description: 3-point control output module, with override switch; for 1 actuator


CLLIONLC01

Centraline Programmable universal HVAC controller, CentraLine LION

DDC controller for all HVAC control applications, and building automation functionalities. The controller can be applied for stand-alone operation, dial-up and in network systems.
For all buildings.
Control software: configurable with COACH software
free programmable with CARE software
programmable with standard ModAL software modules
Hardware inputs: Panel Bus and LON Bus input modules available for:
measurement of temperature, relative humidity, pressure etc.
contact status from relays, thermostats etc.
Hardware outputs: Panel Bus and LON Bus output modules available for:
control devices like servomotors (configuration of safety position is possible)
switching devices like pumps, ventilators
Operator panels: RS232 port available for operator panels CLMMI00N22/CLMMI00N31; these panels can be used for adjustment of setpoints, alarm limits, fixing in/outputs, override functions, graphic trending etc.
Stand-alone operation: yes
Bus system description: communication bus ("physical C-bus" or "C-bus over LON")
LonWorks(R) bus
Panel bus for communication to Panel I/O modules
Transceiver type: LonWorks(R) FTT10A
Mounting: DIN rail
Protection class: IP30
Memory back-up: goldcap capacitor for 72 hours buffer
Power supply: 24Vacdc
Modem connection: directly connectable
C-bus connection: directly connectable
LonWorks(R) connection: directly connectable
Panel bus connection: directly connectable

LION Plant Controller
Product description: Controller


CLLYUB1012S

Centraline Freely programmable BACnet room controller, LYNX

The controllers are for use in VAV (Variable Air Volume) and Unitary HVAC control applications. Each controller communicates via LonWorks(R) or BACnet MS/TP network communications. Each controller provides flexible, universal inputs for external sensors, digital inputs, and a combination of analog outputs and digital Triac outputs. The Sylk Bus is included in each controller which enables connection to other Sylk enabled devices. These controllers provide many options and advanced system features that allow state-of-the-art individual room control. Each controller is freely programmable and configurable. Direct BACnet (MSTP) connection.

Unitary Controllers without pressure sensor and without actuator
Hardware inputs: 1 universal
Hardware outputs: 1 analog, 2 digital
Power supply: 24Vac


CLLYUB4024S

Centraline Freely programmable BACnet room controller, LYNX

The controllers are for use in VAV (Variable Air Volume) and Unitary HVAC control applications. Each controller communicates via LonWorks(R) or BACnet MS/TP network communications. Each controller provides flexible, universal inputs for external sensors, digital inputs, and a combination of analog outputs and digital Triac outputs. The Sylk Bus is included in each controller which enables connection to other Sylk enabled devices. These controllers provide many options and advanced system features that allow state-of-the-art individual room control. Each controller is freely programmable and configurable. Direct BACnet (MSTP) connection.

Unitary Controllers without pressure sensor and without actuator
Hardware inputs: 4 universal
Hardware outputs: 2 analog, 4 digital
Power supply: 24Vac


CLLYVB0000AS

Centraline Freely programmable BACnet room controller, LYNX

The controllers are for use in VAV (Variable Air Volume) and Unitary HVAC control applications. Each controller communicates via LonWorks(R) or BACnet MS/TP network communications. Each controller provides flexible, universal inputs for external sensors, digital inputs, and a combination of analog outputs and digital Triac outputs. The Sylk Bus is included in each controller which enables connection to other Sylk enabled devices. These controllers provide many options and advanced system features that allow state-of-the-art individual room control. Each controller is freely programmable and configurable. Direct BACnet (MSTP) connection.

VAV controllers with pressure sensor and damper actuator 5 Nm
Hardware inputs: no
Hardware outputs: no
Power supply: 24Vac


CLLYVB4022AS

Centraline Freely programmable BACnet room controller, LYNX

The controllers are for use in VAV (Variable Air Volume) and Unitary HVAC control applications. Each controller communicates via LonWorks(R) or BACnet MS/TP network communications. Each controller provides flexible, universal inputs for external sensors, digital inputs, and a combination of analog outputs and digital Triac outputs. The Sylk Bus is included in each controller which enables connection to other Sylk enabled devices. These controllers provide many options and advanced system features that allow state-of-the-art individual room control. Each controller is freely programmable and configurable. Direct BACnet (MSTP) connection.

VAV controllers with pressure sensor and damper actuator 5 Nm
Hardware inputs: 4 universal
Hardware outputs: 2 analog, 2 digital
Power supply: 24Vac


CLLYVB4024NS

Centraline Freely programmable BACnet room controller, LYNX

The controllers are for use in VAV (Variable Air Volume) and Unitary HVAC control applications. Each controller communicates via LonWorks(R) or BACnet MS/TP network communications. Each controller provides flexible, universal inputs for external sensors, digital inputs, and a combination of analog outputs and digital Triac outputs. The Sylk Bus is included in each controller which enables connection to other Sylk enabled devices. These controllers provide many options and advanced system features that allow state-of-the-art individual room control. Each controller is freely programmable and configurable. Direct BACnet (MSTP) connection.

VAV controllers with pressure sensor and without actuator
Hardware inputs: 4 universal
Hardware outputs: 2 analog, 4 digital
Power supply: 24Vac


CLMERL2

Centraline Configurable BACnet room controller MERLIN

The MERLIN (CLMERRxx) family of room controllers provide flexible,configurable, demand-led control delivering tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in todays buildings. These BACnet MS/TP based room controllers are configured through the CL-ROOMUP app, supporting fan coil unit, air quality control, underfloor heating, chilled and hot ceiling as well as radiator heating applications. It is even possible to handle a mix of these applications in one controller.
Line voltage power supply and the flexible use of relays and triacs (24 VAC or 230 VAC), 24 VAC power supply for field devices, Sylk wall modules, and smart engineering and commissioning tools reduce the total installed cost.
Hardware inputs: a variety of sensors (e.g., room temperature sensors, supply temperature sensors, humidity sensors, window sensors, occupancy sensors, and card readers) may be used
contact status from occupancy sensors, window switches, condensation contacts etc.
Hardware outputs: relays with input and output terminal per relay support flexible use (N.O.)
triacs with common input terminals(24/230Vac)
Bus system description: BACnet MS/TP communication between controllers
Sylk bus to Honeywell Room HMIs CLCMTR40x/TR42x
RJ45 connector for BACnet WiFi adapter
Mounting: DIN rail
in cabinets
fuse boxes
on walls
Protection class: IP20 (IP30 with optional terminal cover)
Relay outputs: 4
Control software: configurable

LARGE Housing (189x110x57,5mm)
AO: 2
UI: 6
Triac: 4
Power supply: 230Vac


CLMERL6

Centraline Configurable BACnet room controller MERLIN

The MERLIN (CLMERRxx) family of room controllers provide flexible,configurable, demand-led control delivering tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in todays buildings. These BACnet MS/TP based room controllers are configured through the CL-ROOMUP app, supporting fan coil unit, air quality control, underfloor heating, chilled and hot ceiling as well as radiator heating applications. It is even possible to handle a mix of these applications in one controller.
Line voltage power supply and the flexible use of relays and triacs (24 VAC or 230 VAC), 24 VAC power supply for field devices, Sylk wall modules, and smart engineering and commissioning tools reduce the total installed cost.
Hardware inputs: a variety of sensors (e.g., room temperature sensors, supply temperature sensors, humidity sensors, window sensors, occupancy sensors, and card readers) may be used
contact status from occupancy sensors, window switches, condensation contacts etc.
Hardware outputs: relays with input and output terminal per relay support flexible use (N.O.)
triacs with common input terminals(24/230Vac)
Bus system description: BACnet MS/TP communication between controllers
Sylk bus to Honeywell Room HMIs CLCMTR40x/TR42x
RJ45 connector for BACnet WiFi adapter
Mounting: DIN rail
in cabinets
fuse boxes
on walls
Protection class: IP20 (IP30 with optional terminal cover)
Relay outputs: 4
Control software: configurable

LARGE Housing (189x110x57,5mm)
AO: 6
UI: 10
Triac: 4
Power supply: 24Vac


CLMERL8

Centraline Configurable BACnet room controller MERLIN

The MERLIN (CLMERRxx) family of room controllers provide flexible,configurable, demand-led control delivering tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in todays buildings. These BACnet MS/TP based room controllers are configured through the CL-ROOMUP app, supporting fan coil unit, air quality control, underfloor heating, chilled and hot ceiling as well as radiator heating applications. It is even possible to handle a mix of these applications in one controller.
Line voltage power supply and the flexible use of relays and triacs (24 VAC or 230 VAC), 24 VAC power supply for field devices, Sylk wall modules, and smart engineering and commissioning tools reduce the total installed cost.
Hardware inputs: a variety of sensors (e.g., room temperature sensors, supply temperature sensors, humidity sensors, window sensors, occupancy sensors, and card readers) may be used
contact status from occupancy sensors, window switches, condensation contacts etc.
Hardware outputs: relays with input and output terminal per relay support flexible use (N.O.)
triacs with common input terminals(24/230Vac)
Bus system description: BACnet MS/TP communication between controllers
Sylk bus to Honeywell Room HMIs CLCMTR40x/TR42x
RJ45 connector for BACnet WiFi adapter
Mounting: DIN rail
in cabinets
fuse boxes
on walls
Protection class: IP20 (IP30 with optional terminal cover)
Relay outputs: 4
Control software: configurable

LARGE Housing (189x110x57,5mm)
AO: 6
UI: 10
Triac: 4
Power supply: 230Vac


CLMERS4

Centraline Configurable BACnet room controller MERLIN

The MERLIN (CLMERRxx) family of room controllers provide flexible,configurable, demand-led control delivering tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in todays buildings. These BACnet MS/TP based room controllers are configured through the CL-ROOMUP app, supporting fan coil unit, air quality control, underfloor heating, chilled and hot ceiling as well as radiator heating applications. It is even possible to handle a mix of these applications in one controller.
Line voltage power supply and the flexible use of relays and triacs (24 VAC or 230 VAC), 24 VAC power supply for field devices, Sylk wall modules, and smart engineering and commissioning tools reduce the total installed cost.
Hardware inputs: a variety of sensors (e.g., room temperature sensors, supply temperature sensors, humidity sensors, window sensors, occupancy sensors, and card readers) may be used
contact status from occupancy sensors, window switches, condensation contacts etc.
Hardware outputs: relays with input and output terminal per relay support flexible use (N.O.)
triacs with common input terminals(24/230Vac)
Bus system description: BACnet MS/TP communication between controllers
Sylk bus to Honeywell Room HMIs CLCMTR40x/TR42x
RJ45 connector for BACnet WiFi adapter
Mounting: DIN rail
in cabinets
fuse boxes
on walls
Protection class: IP20 (IP30 with optional terminal cover)
Relay outputs: 4
Control software: configurable

SMALL Housing (162x110x57,5mm)
AO: 4
UI: 4
Triac: 2
Power supply: 230Vac


CLMERS5

Centraline Configurable BACnet room controller MERLIN

The MERLIN (CLMERRxx) family of room controllers provide flexible,configurable, demand-led control delivering tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in todays buildings. These BACnet MS/TP based room controllers are configured through the CL-ROOMUP app, supporting fan coil unit, air quality control, underfloor heating, chilled and hot ceiling as well as radiator heating applications. It is even possible to handle a mix of these applications in one controller.
Line voltage power supply and the flexible use of relays and triacs (24 VAC or 230 VAC), 24 VAC power supply for field devices, Sylk wall modules, and smart engineering and commissioning tools reduce the total installed cost.
Hardware inputs: a variety of sensors (e.g., room temperature sensors, supply temperature sensors, humidity sensors, window sensors, occupancy sensors, and card readers) may be used
contact status from occupancy sensors, window switches, condensation contacts etc.
Hardware outputs: relays with input and output terminal per relay support flexible use (N.O.)
triacs with common input terminals(24/230Vac)
Bus system description: BACnet MS/TP communication between controllers
Sylk bus to Honeywell Room HMIs CLCMTR40x/TR42x
RJ45 connector for BACnet WiFi adapter
Mounting: DIN rail
in cabinets
fuse boxes
on walls
Protection class: IP20 (IP30 with optional terminal cover)
Relay outputs: 4
Control software: configurable

SMALL Housing (162x110x57,5mm)
AO: 4
UI: 4
Triac: 2
Power supply: 24Vac


CLMMI00N22

Centraline CentraLine External MMI

MMI with a backlit LCD screen capable of displaying West European, East European, Turkish, and Cyrillic characters. Suitable for use as a desk-top device or for installation in a cabinet door. Bus-wide access to all CentraLine plant controllers on the same bus.
Kit supplied for panel door mounting (IP54)


CLMMI00N31

Centraline Programmable universal BACnet Building Controller, EAGLE
Additional product for controllers

CentraLine Touch operator interface



CLNX-100N-SMA-1Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-100N maintenance 1 year extension


CLNX-100N-SMA-3Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-100N maintenance 3 year extension


CLNX-100N-SMA-5Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-100N maintenance 5 year extension


CLNX-10N-SMA-1Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-10N maintenance 1 year extension


CLNX-10N-SMA-3Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-10N maintenance 3 year extension


CLNX-10N-SMA-5Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-10N maintenance 5 year extension


CLNX-1N-SMA-1Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-1N maintenance 1 year extension


CLNX-1N-SMA-3Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-1N maintenance 3 year extension


CLNX-1N-SMA-5Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-1N maintenance 5 year extension


CLNX-ALM-PORTLAB

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Alarm Console
Model: ARENA NX alarm portal


CLNX-DEVICE-UP-10

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 point upgrade licenses
Product description: Plus 500 points upgrade


CLNX-DEVICE-UP-25

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 point upgrade licenses
Product description: Plus 1250 points upgrade


CLNX-DEVICE-UP-50

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 point upgrade licenses
Product description: Plus 2500 points upgrade


CLNX-DR-MFID

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Fidelio Driver
Model: Fidelio driver for ARENA NX and HAWK8000


CLNX-DR-S-CSV

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

Optional ARENA NX database drivers for external database applications
Model: Driver for CSV database


CLNX-DR-S-MYSQL

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

Optional ARENA NX database drivers for external database applications
Model: Driver for MYSQL database


CLNX-DR-SMS-ALM

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Communication drivers

HAWK 8000 SMS driver



CLNX-DR-SQL

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

Optional ARENA NX database drivers for external database applications
Model: Driver for SQL database


CLNX-HAWK8-DEMO

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Communication drivers

HAWK 8000 Demo license



CLNX-JACE-8000-AX

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Communication drivers

HAWK 8000 Downgrade to run Niagara AX



CLNX-P-SMA-1Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for point licenses
Model: SUP-P maintenance 3 year extension


CLNX-P-SMA-5Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for point licenses
Model: SUP-P maintenance 5 year extension


CLNX-S-10000P

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers with open point licenses
Model: NX Supervisor with 10000 open points


CLNX-S-10000P-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add driver capacity 10000 points


CLNX-S-100N

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers based on NIAGARA nodes
Model: Supervisor - 100 HAWK / EAGLHAWK


CLNX-S-100N-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Upgrade to 100 HAWK / EAGLEHAWK


CLNX-S-10N

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers based on NIAGARA nodes
Model: Supervisor - 10 HAWK / EAGLHAWK


CLNX-S-10N-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add 10 HAWK / EAGLEHAWK


CLNX-S-1N-200PP-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add 1 HAWK / EAGLEHAWK adds another 200 proxy points. One controller could have 100 another one 300 points.


CLNX-S-1N-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add 1 HAWK / EAGLEHAWK


CLNX-S-2500P

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers with open point licenses
Model: NX Supervisor with 2500 open points


CLNX-S-2500P-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add driver capacity 2500 points


CLNX-S-50000P

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers with open point licenses
Model: NX Supervisor with 50000 open points


CLNX-S-50000P-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add driver capacity 50000 points


CLNX-S-5000P

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers with open point licenses
Model: NX Supervisor with 5000 open points


CLNX-S-5000P-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add driver capacity 5000 points


CLNX-S-500P

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers with open point licenses
Model: NX Supervisor with 500 open points


CLNX-S-500P-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Add driver capacity 500 points


CLNX-S-5N

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers based on NIAGARA nodes
Model: Supervisor - 5 HAWK / EAGLHAWK


CLNX-S-UNL

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers based on NIAGARA nodes
Model: Supervisor - unlimited HAWK / EAGLHAWK - only on request, NOTE: Licenses of FOX nodes are indicated by the suffix "N" in the part number


CLNX-S-UNLN-UP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX Upgrade Licenses
Model: Upgrade to unlimited number HAWK / EAGLEHAWK


CLNX-SMA-80010-1YR

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 software update licenses
Product description: 1 year software update for 500-1249 points


CLNX-SMA-8005-1YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 1 year software update for 250-499 points


CLNX-SMA-8005-3YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 3 year software update for 250-499 points


CLNX-SMA-8005-5YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 5 year software update for 250-499 points


CLNX-SMA-8010-1YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 1 year software update for 500-1249 points


CLNX-SMA-8010-3YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 3 year software update for 500-1249 points


CLNX-SMA-8010-5YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 5 year software update for 500-1249 points


CLNX-SMA-8025-1YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 1 year software update for 1250-4999 points


CLNX-SMA-8025-3YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 3 year software update for 1250-4999 points


CLNX-SMA-8025-5YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 5 year software update for 1250-4999 points


CLNX-SMA-8100-1YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 1 year software update for 5000-9999 points


CLNX-SMA-8100-3YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 3 year software update for 5000-9999 points


CLNX-SMA-8100-5YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 5 year software update for 5000-9999 points


CLNX-SMA-8200-1YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 1 year software update for 10000+ points


CLNX-SMA-8200-3YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 3 year software update for 10000+ points


CLNX-SMA-8200-5YR

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

EAGLEHAWK software update licenses
Product description: 5 year software update for 10000+ points


CLNX-UNL-SMA-1Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-UNLN maintenance 3 year extension


CLNX-UNL-SMA-5Y

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX maintenance licenses for node licenses
Model: SUP-UNLN maintenance 5 year extension


CLNXEH-DEMO

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: Demo license, expires after 12 months.


CLNXEH-DEVICE-UP-1

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 50 open points


CLNXEH-DEVICE-UP10

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 500 open points


CLNXEH-DEVICE-UP25

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 1250 open points


CLNXEH-DEVICE-UP50

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 2500 open points


CLNXEH00D100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with onboard HMI, without onboard IO. Includes licenses for 255 Panel-Bus/Onboard IO points, 100 open points and first year of Software Maintenance Agreement.


CLNXEH00ND100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller without onboard IO. Includes licenses for 255 Panel-Bus/Onboard IO points, 100 open points and first year of Software Maintenance Agreement.


CLNXEH14D100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with onboard HMI, with 14 onboard IO. Includes licenses for 255 Panel-Bus/Onboard IO points, 100 open points and first year of Software Maintenance Agreement.


CLNXEH14ND100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with 14 onboard IO. Includes licenses for 255 Panel-Bus/Onboard IO points, 100 open points and first year of Software Maintenance Agreement.


CLNXEH26D100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with onboard HMI, with 26 onboard IO. Includes licenses for 255 Panel-Bus/Onboard IO points, 100 open points and first year of Software Maintenance Agreement.


CLNXEH26ND100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with 26 onboard IO. Includes licenses for 255 Panel-Bus/Onboard IO points, 100 open points and first year of Software Maintenance Agreement.


CLNXEHPB100UP

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 102 Panel-Bus/Onboard IO points


CLNXEHPB255UP

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 255 Panel-Bus/Onboard IO points


CLNXEHRBAC250UP

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 250 Honeywell BACnet integration points


CLNXEHRLON250UP

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

License upgrades
Product description: License upgrade with 250 Honeywell LON integration points


CLNXEHS00D100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller without onboard IO. Includes licenses for 100 Panel-Bus/Onboard IO/ Open points. Without Software Maintenance Agreement.


CLNXEHS00ND100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller without onboard IO. Includes licenses for 100 Panel-Bus/Onboard IO/ Open points. Without Software Maintenance Agreement.


CLNXEHS14D100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with onboard HMI, with 14 onboard IO. Includes licenses for 100 Panel-Bus/Onboard IO/ Open points. Without Software Maintenance Agreement.


CLNXEHS14ND100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with 14 onboard IO. Includes licenses for 100 Panel-Bus/Onboard IO/ Open points. Without Software Maintenance Agreement.


CLNXEHS26D100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with onboard HMI, with 26 onboard IO. Includes licenses for 100 Panel-Bus/Onboard IO/ Open points. Without Software Maintenance Agreement.


CLNXEHS26ND100A

Centraline EAGLEHAWK NX Integrated Plant Control

EAGLEHAWK is a powerful Hardware and Software platform designed to manage HVAC and non-HVAC Systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protools, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. Eaglehawk allows to make use of the CentraLine Application Library, which ensures unparalleled energy Efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports, 1 RS232 port.
Hardware inputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus input modules available for: measurement of temperature, relative humidity, pressure etc.; contact status from relays, thermostats; counters etc.
Hardware outputs: Controllers available with 0, 14 or 26 onboard inputs/outputs
Panel-Bus output modules available for: control devices like servomotors, switching devices like pumps, ventilators etc.
Operator panels: EAGLEHAWK is operated via a standard browser. By default, an integrated web-server provides all freely programmable operation pages for full and JAVA-free browser-based operation
Through the consistent use of software standards, any PC platform can be used as an operator interface (client), including laptops, desktops PCs, or touch screen PCs for direct flush mounting into electrical panel doors (IP65)
For mobile devices, freely programmable web-pages can be made available
Management applications: ARENA NX
Mounting: in panels
in fuse boxes conforming with standard DIN43880, and having a slot height of max. 45 mm
in panel front doors (using accessory MVC-80-AC2)
on walls (using accessory MVC-80-AC1)
Protection class: IP20 (IP30 when mounted through cabinet doors with accessory MVC-80-AC2)
Power supply: 19..29 Vac or 20..30 Vdc ; 9 VA
Real-time clock back-up with goldcap capacitor for 72 hours buffer
Use PW3, PW20 or PW60, for M-Bus interfacing
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON FTT10A and IP, KNX/IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements: Panel-Bus , C-Bus, LON IO, BACnet Integration, Project Documentation and Print-Out, IO Creation, EnOcean, MQTT
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming, Cyber Security
Web Server: Supports most common mobile and PC browsers
Provides JAVA-free web-pages (HTML5)
Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option
Programming via COACH NX
EAGLEHAWK incorporates industry best practices for cyber security. This includes features such as secure boot, encrypted file system, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers
Onboard and detached HMIs
EAGLEHAWK is optionally available with a network independent HMI in two variants:
Onboard HMI: Integrated HMI with graphic icons, push&turn wheel and direct access buttons.Configurable operation menu, which among many more includes configurable fast access lists that can contain data-points, parameters and time schedules.The onboard HMI allows for adaptation of the operating menu to application- specific needs. The onboard HMI is independent from the BMS network and hence suitable for emergency operation as is required in many project specifications.
Detached HMI: CLEAHMI21 see also separate description further down. Same as above, but as a separate unit. Allows for mounting through panel doors, onto walls, magnetic mounting and hand-held.

Controller
Product description: EAGLEHAWK controller with 26 onboard IO. Includes licenses for 100 Panel-Bus/Onboard IO/ Open points. Without Software Maintenance Agreement.


CLNXEMC12

Centraline ENERGY VISION NX

ENERGY VISION NX is an energy benchmarking and analysis tool, developed for the HVAC market, built on Niagara NX using HTML5 technology, providing a large range of techniques for managing all aspects of energy related data. EnergyVision NX is the ideal system to:
help manage energy, analyse and optimise the operation of facilities
measure performance across multiple levels within your building or estate
It is fully web-enabled and able to integrate data from a wide range of existing systems. HAWK and ARENA AX can provide data from most of the metering devices used in the market. It enables an integrated solution, allowing the user to collate and manage all aspects of their energy data at a central location.
FEATURES and BENEFITS
Completely integrated into Niagara NX: Save costs. No additional equipment needed. Get metering data from most of the metering communication protocols in the market.
Automatically collect and aggregate metering data: No need for expensive data collection devices. Reliable and continuous data collection. No need to send the housekeeper to note metering data.
Monitor energy consumption with daily, weekly, monthly or annual profiles: Easily recognize waste of energy.
Analyse energy profiles: Detect waste of energy. Optimize energy efficiency.
Translate raw energy values into monetary units: Always have an overview of the energy costs. Compare actual costs with budget.
Energy Benchmarking graphs, with daily, weekly, monthly, yearly views: Prove the efficiency of your energy saving actions. Easily understand how your energy consumption is against target profiles or historical consumptions.
Visualization and ranking of consumption between meters, zones, systems, buildings, sites: Get an overview of your highest consumers. Start optimizing your energy efficiency, where you can achieve the biggest savings.
Instant and automatic reports for users, energy managers and auditors: Save costs for generating energy reports. Have the relevant data for energy managers and auditors with highest accuracy and just in time.
Kiosk Mode - a rotating sequence of easy understandable energy efficiency data: Use in a building foyer or reception area to raise occupants awareness.
Honeywell offers the complete meter portfolio: Honeywell offers all the needed metering devices starting from one and three phase electrical meters, heating, cooling energy meters, hot and cold water meters and all kinds of flow meters.
Cost-efficient solution: Logos/layout can be customized free of charge. All components are part of an AX palette low effort for technical support. Existing BACnet Schedules can be used. Existing BACnet Schedules can be used.
Low training effort for engineers and users: Low training efforts for customers and partners/ engineers. Training video are available on the partner web. Very easy installation and start-up.
Cyber Security: Applies latest cyber security Standards.
HTML5 view for smartphones, tablets and PC.


Product description: ENERGY VISION controller base license 12 meter points. (No upgrades)


CLNXEMS100-UP

Centraline ENERGY VISION NX

ENERGY VISION NX is an energy benchmarking and analysis tool, developed for the HVAC market, built on Niagara NX using HTML5 technology, providing a large range of techniques for managing all aspects of energy related data. EnergyVision NX is the ideal system to:
help manage energy, analyse and optimise the operation of facilities
measure performance across multiple levels within your building or estate
It is fully web-enabled and able to integrate data from a wide range of existing systems. HAWK and ARENA AX can provide data from most of the metering devices used in the market. It enables an integrated solution, allowing the user to collate and manage all aspects of their energy data at a central location.
FEATURES and BENEFITS
Completely integrated into Niagara NX: Save costs. No additional equipment needed. Get metering data from most of the metering communication protocols in the market.
Automatically collect and aggregate metering data: No need for expensive data collection devices. Reliable and continuous data collection. No need to send the housekeeper to note metering data.
Monitor energy consumption with daily, weekly, monthly or annual profiles: Easily recognize waste of energy.
Analyse energy profiles: Detect waste of energy. Optimize energy efficiency.
Translate raw energy values into monetary units: Always have an overview of the energy costs. Compare actual costs with budget.
Energy Benchmarking graphs, with daily, weekly, monthly, yearly views: Prove the efficiency of your energy saving actions. Easily understand how your energy consumption is against target profiles or historical consumptions.
Visualization and ranking of consumption between meters, zones, systems, buildings, sites: Get an overview of your highest consumers. Start optimizing your energy efficiency, where you can achieve the biggest savings.
Instant and automatic reports for users, energy managers and auditors: Save costs for generating energy reports. Have the relevant data for energy managers and auditors with highest accuracy and just in time.
Kiosk Mode - a rotating sequence of easy understandable energy efficiency data: Use in a building foyer or reception area to raise occupants awareness.
Honeywell offers the complete meter portfolio: Honeywell offers all the needed metering devices starting from one and three phase electrical meters, heating, cooling energy meters, hot and cold water meters and all kinds of flow meters.
Cost-efficient solution: Logos/layout can be customized free of charge. All components are part of an AX palette low effort for technical support. Existing BACnet Schedules can be used. Existing BACnet Schedules can be used.
Low training effort for engineers and users: Low training efforts for customers and partners/ engineers. Training video are available on the partner web. Very easy installation and start-up.
Cyber Security: Applies latest cyber security Standards.
HTML5 view for smartphones, tablets and PC.


Product description: ENERGY VISION supervisor license add 100 meter points


CLNXEMS1K-UP

Centraline ENERGY VISION NX

ENERGY VISION NX is an energy benchmarking and analysis tool, developed for the HVAC market, built on Niagara NX using HTML5 technology, providing a large range of techniques for managing all aspects of energy related data. EnergyVision NX is the ideal system to:
help manage energy, analyse and optimise the operation of facilities
measure performance across multiple levels within your building or estate
It is fully web-enabled and able to integrate data from a wide range of existing systems. HAWK and ARENA AX can provide data from most of the metering devices used in the market. It enables an integrated solution, allowing the user to collate and manage all aspects of their energy data at a central location.
FEATURES and BENEFITS
Completely integrated into Niagara NX: Save costs. No additional equipment needed. Get metering data from most of the metering communication protocols in the market.
Automatically collect and aggregate metering data: No need for expensive data collection devices. Reliable and continuous data collection. No need to send the housekeeper to note metering data.
Monitor energy consumption with daily, weekly, monthly or annual profiles: Easily recognize waste of energy.
Analyse energy profiles: Detect waste of energy. Optimize energy efficiency.
Translate raw energy values into monetary units: Always have an overview of the energy costs. Compare actual costs with budget.
Energy Benchmarking graphs, with daily, weekly, monthly, yearly views: Prove the efficiency of your energy saving actions. Easily understand how your energy consumption is against target profiles or historical consumptions.
Visualization and ranking of consumption between meters, zones, systems, buildings, sites: Get an overview of your highest consumers. Start optimizing your energy efficiency, where you can achieve the biggest savings.
Instant and automatic reports for users, energy managers and auditors: Save costs for generating energy reports. Have the relevant data for energy managers and auditors with highest accuracy and just in time.
Kiosk Mode - a rotating sequence of easy understandable energy efficiency data: Use in a building foyer or reception area to raise occupants awareness.
Honeywell offers the complete meter portfolio: Honeywell offers all the needed metering devices starting from one and three phase electrical meters, heating, cooling energy meters, hot and cold water meters and all kinds of flow meters.
Cost-efficient solution: Logos/layout can be customized free of charge. All components are part of an AX palette low effort for technical support. Existing BACnet Schedules can be used. Existing BACnet Schedules can be used.
Low training effort for engineers and users: Low training efforts for customers and partners/ engineers. Training video are available on the partner web. Very easy installation and start-up.
Cyber Security: Applies latest cyber security Standards.
HTML5 view for smartphones, tablets and PC.


Product description: ENERGY VISION supervisor license add 1000 meter points


CLNXEMS25

Centraline ENERGY VISION NX

ENERGY VISION NX is an energy benchmarking and analysis tool, developed for the HVAC market, built on Niagara NX using HTML5 technology, providing a large range of techniques for managing all aspects of energy related data. EnergyVision NX is the ideal system to:
help manage energy, analyse and optimise the operation of facilities
measure performance across multiple levels within your building or estate
It is fully web-enabled and able to integrate data from a wide range of existing systems. HAWK and ARENA AX can provide data from most of the metering devices used in the market. It enables an integrated solution, allowing the user to collate and manage all aspects of their energy data at a central location.
FEATURES and BENEFITS
Completely integrated into Niagara NX: Save costs. No additional equipment needed. Get metering data from most of the metering communication protocols in the market.
Automatically collect and aggregate metering data: No need for expensive data collection devices. Reliable and continuous data collection. No need to send the housekeeper to note metering data.
Monitor energy consumption with daily, weekly, monthly or annual profiles: Easily recognize waste of energy.
Analyse energy profiles: Detect waste of energy. Optimize energy efficiency.
Translate raw energy values into monetary units: Always have an overview of the energy costs. Compare actual costs with budget.
Energy Benchmarking graphs, with daily, weekly, monthly, yearly views: Prove the efficiency of your energy saving actions. Easily understand how your energy consumption is against target profiles or historical consumptions.
Visualization and ranking of consumption between meters, zones, systems, buildings, sites: Get an overview of your highest consumers. Start optimizing your energy efficiency, where you can achieve the biggest savings.
Instant and automatic reports for users, energy managers and auditors: Save costs for generating energy reports. Have the relevant data for energy managers and auditors with highest accuracy and just in time.
Kiosk Mode - a rotating sequence of easy understandable energy efficiency data: Use in a building foyer or reception area to raise occupants awareness.
Honeywell offers the complete meter portfolio: Honeywell offers all the needed metering devices starting from one and three phase electrical meters, heating, cooling energy meters, hot and cold water meters and all kinds of flow meters.
Cost-efficient solution: Logos/layout can be customized free of charge. All components are part of an AX palette low effort for technical support. Existing BACnet Schedules can be used. Existing BACnet Schedules can be used.
Low training effort for engineers and users: Low training efforts for customers and partners/ engineers. Training video are available on the partner web. Very easy installation and start-up.
Cyber Security: Applies latest cyber security Standards.
HTML5 view for smartphones, tablets and PC.


Product description: ENERGY VISION supervisor base license 25 meter points


CLNXEMS50-UP

Centraline ENERGY VISION NX

ENERGY VISION NX is an energy benchmarking and analysis tool, developed for the HVAC market, built on Niagara NX using HTML5 technology, providing a large range of techniques for managing all aspects of energy related data. EnergyVision NX is the ideal system to:
help manage energy, analyse and optimise the operation of facilities
measure performance across multiple levels within your building or estate
It is fully web-enabled and able to integrate data from a wide range of existing systems. HAWK and ARENA AX can provide data from most of the metering devices used in the market. It enables an integrated solution, allowing the user to collate and manage all aspects of their energy data at a central location.
FEATURES and BENEFITS
Completely integrated into Niagara NX: Save costs. No additional equipment needed. Get metering data from most of the metering communication protocols in the market.
Automatically collect and aggregate metering data: No need for expensive data collection devices. Reliable and continuous data collection. No need to send the housekeeper to note metering data.
Monitor energy consumption with daily, weekly, monthly or annual profiles: Easily recognize waste of energy.
Analyse energy profiles: Detect waste of energy. Optimize energy efficiency.
Translate raw energy values into monetary units: Always have an overview of the energy costs. Compare actual costs with budget.
Energy Benchmarking graphs, with daily, weekly, monthly, yearly views: Prove the efficiency of your energy saving actions. Easily understand how your energy consumption is against target profiles or historical consumptions.
Visualization and ranking of consumption between meters, zones, systems, buildings, sites: Get an overview of your highest consumers. Start optimizing your energy efficiency, where you can achieve the biggest savings.
Instant and automatic reports for users, energy managers and auditors: Save costs for generating energy reports. Have the relevant data for energy managers and auditors with highest accuracy and just in time.
Kiosk Mode - a rotating sequence of easy understandable energy efficiency data: Use in a building foyer or reception area to raise occupants awareness.
Honeywell offers the complete meter portfolio: Honeywell offers all the needed metering devices starting from one and three phase electrical meters, heating, cooling energy meters, hot and cold water meters and all kinds of flow meters.
Cost-efficient solution: Logos/layout can be customized free of charge. All components are part of an AX palette low effort for technical support. Existing BACnet Schedules can be used. Existing BACnet Schedules can be used.
Low training effort for engineers and users: Low training efforts for customers and partners/ engineers. Training video are available on the partner web. Very easy installation and start-up.
Cyber Security: Applies latest cyber security Standards.
HTML5 view for smartphones, tablets and PC.


Product description: ENERGY VISION supervisor license add 50 meter points


CLNXEMS500-UP

Centraline ENERGY VISION NX

ENERGY VISION NX is an energy benchmarking and analysis tool, developed for the HVAC market, built on Niagara NX using HTML5 technology, providing a large range of techniques for managing all aspects of energy related data. EnergyVision NX is the ideal system to:
help manage energy, analyse and optimise the operation of facilities
measure performance across multiple levels within your building or estate
It is fully web-enabled and able to integrate data from a wide range of existing systems. HAWK and ARENA AX can provide data from most of the metering devices used in the market. It enables an integrated solution, allowing the user to collate and manage all aspects of their energy data at a central location.
FEATURES and BENEFITS
Completely integrated into Niagara NX: Save costs. No additional equipment needed. Get metering data from most of the metering communication protocols in the market.
Automatically collect and aggregate metering data: No need for expensive data collection devices. Reliable and continuous data collection. No need to send the housekeeper to note metering data.
Monitor energy consumption with daily, weekly, monthly or annual profiles: Easily recognize waste of energy.
Analyse energy profiles: Detect waste of energy. Optimize energy efficiency.
Translate raw energy values into monetary units: Always have an overview of the energy costs. Compare actual costs with budget.
Energy Benchmarking graphs, with daily, weekly, monthly, yearly views: Prove the efficiency of your energy saving actions. Easily understand how your energy consumption is against target profiles or historical consumptions.
Visualization and ranking of consumption between meters, zones, systems, buildings, sites: Get an overview of your highest consumers. Start optimizing your energy efficiency, where you can achieve the biggest savings.
Instant and automatic reports for users, energy managers and auditors: Save costs for generating energy reports. Have the relevant data for energy managers and auditors with highest accuracy and just in time.
Kiosk Mode - a rotating sequence of easy understandable energy efficiency data: Use in a building foyer or reception area to raise occupants awareness.
Honeywell offers the complete meter portfolio: Honeywell offers all the needed metering devices starting from one and three phase electrical meters, heating, cooling energy meters, hot and cold water meters and all kinds of flow meters.
Cost-efficient solution: Logos/layout can be customized free of charge. All components are part of an AX palette low effort for technical support. Existing BACnet Schedules can be used. Existing BACnet Schedules can be used.
Low training effort for engineers and users: Low training efforts for customers and partners/ engineers. Training video are available on the partner web. Very easy installation and start-up.
Cyber Security: Applies latest cyber security Standards.
HTML5 view for smartphones, tablets and PC.


Product description: ENERGY VISION supervisor license add 500 meter points


CLNXHAWK8-100

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, without WIFI
Product description: HAWK 8000, no WIFI, 100 points, one year software update


CLNXHAWK8-10K

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, without WIFI
Product description: HAWK 8000, no WIFI, 10000 points, one year software update


CLNXHAWK8-1250

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, without WIFI
Product description: HAWK 8000, no WIFI, 1250 points, one year software update


CLNXHAWK8-250

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, without WIFI
Product description: HAWK 8000, no WIFI, 250 points, one year software update


CLNXHAWK8-500

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, without WIFI
Product description: HAWK 8000, no WIFI, 500 points, one year software update


CLNXHAWK8-5K

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, without WIFI
Product description: HAWK 8000, no WIFI, 5000 points, one year software update


CLNXHAWK8-CLIP

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Spare parts

HAWK 8000 CentraLine clip



CLNXHAWK8-SD

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Spare parts

HAWK 8000 SD CARD



CLNXHAWK8W02-100

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, with WIFI
Product description: HAWK 8000, with WIFI, 100 points, one year software update


CLNXHAWK8W02-10K

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, with WIFI
Product description: HAWK 8000, with WIFI, 10000 points, one year software update


CLNXHAWK8W02-1250

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, with WIFI
Product description: HAWK 8000, with WIFI, 1250 points, one year software update


CLNXHAWK8W02-250

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, with WIFI
Product description: HAWK 8000, with WIFI, 250 points, one year software update


CLNXHAWK8W02-500

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, with WIFI
Product description: HAWK 8000, with WIFI, 500 points, one year software update


CLNXHAWK8W02-5K

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000, with WIFI
Product description: HAWK 8000, with WIFI, 5000 points, one year software update


CLNXSERIES8

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Spare parts

HAWK 8000, no WIFI, without license



CLNXSERIES8W02

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Spare parts

HAWK 8000, with WIFI, without license



CLPA13LC02

Centraline HVAC controller with configurable applications, PANTHER

CentraLine controller for HVAC applications The controller can be applied for stand-alone operation, dial-up and in network systems.
Control software: Free programmable with CARE software or configurable with COACH engineering tool. Application card with control software, with hundreds of different selectable applications and parameter settings.
Hardware inputs: Analog Inputs (AI) for NTC20k sensors
Digital Inputs (DI) for potential free contacts or 24 Vdc
Hardware outputs: Analogue Outputs (AO) 0..10 Vdc
Digital Outputs (DO) 24 Vac
Management applications: ARENA 3.00
Stand-alone operation: yes
Bus system description: LonWorks(R) bus for data exchange with other PANTHER, or TIGER controllers, and building automation management systems with ARENA, or alarm monitoring with RANGER
models available with C-bus, for data exchange with other PANTHER or MCR200 controllers (max. 30 devices per bus)
Transceiver type: LonWorks(R) FTT10A
Application cards: with removable card for communication, application storage, operating system and local language texts for operator panel
Mounting: DIN rail or cabinet front door
Protection class: IP30, IP54 with door mounting accessories (supplied)
Type of terminals: screw terminals with terminal block
Memory back-up: goldcap capacitor for 72 hours RAM and real-time clock buffering
Power supply: 24Vac
C-bus connection: directly connectable via application card
LonWorks(R) connection: directly connectable via application card
Use CARE software for free programming or COACH software to select the right control application for the required installation.

Mini PANTHER controller; 4 AI, 4 DI, 2 AO, 3 DO
Product description: Mini PANTHER controller with LON + C-Bus


CLPA13LC12

Centraline HVAC controller with configurable applications, PANTHER

CentraLine controller for HVAC applications The controller can be applied for stand-alone operation, dial-up and in network systems.
Control software: Free programmable with CARE software or configurable with COACH engineering tool. Application card with control software, with hundreds of different selectable applications and parameter settings.
Hardware inputs: Analog Inputs (AI) for NTC20k sensors
Digital Inputs (DI) for potential free contacts or 24 Vdc
Hardware outputs: Analogue Outputs (AO) 0..10 Vdc
Digital Outputs (DO) 24 Vac
Management applications: ARENA 3.00
Stand-alone operation: yes
Bus system description: LonWorks(R) bus for data exchange with other PANTHER, or TIGER controllers, and building automation management systems with ARENA, or alarm monitoring with RANGER
models available with C-bus, for data exchange with other PANTHER or MCR200 controllers (max. 30 devices per bus)
Transceiver type: LonWorks(R) FTT10A
Application cards: with removable card for communication, application storage, operating system and local language texts for operator panel
Mounting: DIN rail or cabinet front door
Protection class: IP30, IP54 with door mounting accessories (supplied)
Type of terminals: screw terminals with terminal block
Memory back-up: goldcap capacitor for 72 hours RAM and real-time clock buffering
Power supply: 24Vac
C-bus connection: directly connectable via application card
LonWorks(R) connection: directly connectable via application card
Use CARE software for free programming or COACH software to select the right control application for the required installation.

Mini PANTHER controller; 4 AI, 4 DI, 2 AO, 3 DO
Product description: Mini PANTHER controller with LON + C-Bus + operator panel


CLPA21LC02

Centraline HVAC controller with configurable applications, PANTHER

CentraLine controller for HVAC applications The controller can be applied for stand-alone operation, dial-up and in network systems.
Control software: Free programmable with CARE software or configurable with COACH engineering tool. Application card with control software, with hundreds of different selectable applications and parameter settings.
Hardware inputs: Analog Inputs (AI) for NTC20k sensors
Digital Inputs (DI) for potential free contacts or 24 Vdc
Hardware outputs: Analogue Outputs (AO) 0..10 Vdc
Digital Outputs (DO) 24 Vac
Management applications: ARENA 3.00
Stand-alone operation: yes
Bus system description: LonWorks(R) bus for data exchange with other PANTHER, or TIGER controllers, and building automation management systems with ARENA, or alarm monitoring with RANGER
models available with C-bus, for data exchange with other PANTHER or MCR200 controllers (max. 30 devices per bus)
Transceiver type: LonWorks(R) FTT10A
Application cards: with removable card for communication, application storage, operating system and local language texts for operator panel
Mounting: DIN rail or cabinet front door
Protection class: IP30, IP54 with door mounting accessories (supplied)
Type of terminals: screw terminals with terminal block
Memory back-up: goldcap capacitor for 72 hours RAM and real-time clock buffering
Power supply: 24Vac
C-bus connection: directly connectable via application card
LonWorks(R) connection: directly connectable via application card
Use CARE software for free programming or COACH software to select the right control application for the required installation.

PANTHER controller; 8 AI, 4 DI, 4 AO, 6 DO
Product description: PANTHER controller with LON + C-Bus


CLPA21LC12

Centraline HVAC controller with configurable applications, PANTHER

CentraLine controller for HVAC applications The controller can be applied for stand-alone operation, dial-up and in network systems.
Control software: Free programmable with CARE software or configurable with COACH engineering tool. Application card with control software, with hundreds of different selectable applications and parameter settings.
Hardware inputs: Analog Inputs (AI) for NTC20k sensors
Digital Inputs (DI) for potential free contacts or 24 Vdc
Hardware outputs: Analogue Outputs (AO) 0..10 Vdc
Digital Outputs (DO) 24 Vac
Management applications: ARENA 3.00
Stand-alone operation: yes
Bus system description: LonWorks(R) bus for data exchange with other PANTHER, or TIGER controllers, and building automation management systems with ARENA, or alarm monitoring with RANGER
models available with C-bus, for data exchange with other PANTHER or MCR200 controllers (max. 30 devices per bus)
Transceiver type: LonWorks(R) FTT10A
Application cards: with removable card for communication, application storage, operating system and local language texts for operator panel
Mounting: DIN rail or cabinet front door
Protection class: IP30, IP54 with door mounting accessories (supplied)
Type of terminals: screw terminals with terminal block
Memory back-up: goldcap capacitor for 72 hours RAM and real-time clock buffering
Power supply: 24Vac
C-bus connection: directly connectable via application card
LonWorks(R) connection: directly connectable via application card
Use CARE software for free programming or COACH software to select the right control application for the required installation.

PANTHER controller; 8 AI, 4 DI, 4 AO, 6 DO
Product description: PANTHER controller with LON + C-Bus + operator panel


CLPA21LC22

Centraline HVAC controller with configurable applications, PANTHER

CentraLine controller for HVAC applications The controller can be applied for stand-alone operation, dial-up and in network systems.
Control software: Free programmable with CARE software or configurable with COACH engineering tool. Application card with control software, with hundreds of different selectable applications and parameter settings.
Hardware inputs: Analog Inputs (AI) for NTC20k sensors
Digital Inputs (DI) for potential free contacts or 24 Vdc
Hardware outputs: Analogue Outputs (AO) 0..10 Vdc
Digital Outputs (DO) 24 Vac
Management applications: ARENA 3.00
Stand-alone operation: yes
Bus system description: LonWorks(R) bus for data exchange with other PANTHER, or TIGER controllers, and building automation management systems with ARENA, or alarm monitoring with RANGER
models available with C-bus, for data exchange with other PANTHER or MCR200 controllers (max. 30 devices per bus)
Transceiver type: LonWorks(R) FTT10A
Application cards: with removable card for communication, application storage, operating system and local language texts for operator panel
Mounting: DIN rail or cabinet front door
Protection class: IP30, IP54 with door mounting accessories (supplied)
Type of terminals: screw terminals with terminal block
Memory back-up: goldcap capacitor for 72 hours RAM and real-time clock buffering
Power supply: 24Vac
C-bus connection: directly connectable via application card
LonWorks(R) connection: directly connectable via application card
Use CARE software for free programming or COACH software to select the right control application for the required installation.

PANTHER controller; 8 AI, 4 DI, 4 AO, 6 DO
Product description: PANTHER controller with LON + C-Bus + operator panel Cyrillic


CLSE1L230

Centraline Zone controller, SERVAL

Room temperature controller for 2- and 4-pipe fan coil units, radiators, floorheating and chilled ceiling.
For heater, cooler, electric re-heat and 1,2,3-speed fans.
Heating output signal: triacs (500 mA) configurable for thermal, 3-pt or PWM control
Cooling output signal: triacs (500 mA) configurable for thermal or 3-pt control
Fan output signal: 3 relays (250V~, 3A)
Re-heat output signal: relay (250V~, 10A) (6A UL916)
Control functions: heat only, cool only, heat/cool change over, heat and cool in sequence; in addition electrical reheat; zero energy band
Modes of operation: occupied, standby, unoccupied, open window, frost protection, smoke control, fan fail, summer/winter change over
Obligatory inputs: 1 temperature input for CentraLine wall module
Optional inputs: configurable with COACH:
1 digital input configurable for: window or occupancy or or movement or change over or airflow
1 digital input for window contact
Stand-alone operation: yes
Network operation: yes
Bus system: LonWorks(R)
LonMark(R) profile: 8020
Use COACH software from CentraLine to select the right control software for the required installation.


Power supply: 230Vac
Re-heat output: yes
Triac outputs 24Vac: no
Triac outputs 230Vac: 4x for heat/cool
Auxiliary output signal: no
Note: no


CLSE1L24

Centraline Zone controller, SERVAL

Room temperature controller for 2- and 4-pipe fan coil units, radiators, floorheating and chilled ceiling.
For heater, cooler, electric re-heat and 1,2,3-speed fans.
Heating output signal: triacs (500 mA) configurable for thermal, 3-pt or PWM control
Cooling output signal: triacs (500 mA) configurable for thermal or 3-pt control
Fan output signal: 3 relays (250V~, 3A)
Re-heat output signal: relay (250V~, 10A) (6A UL916)
Control functions: heat only, cool only, heat/cool change over, heat and cool in sequence; in addition electrical reheat; zero energy band
Modes of operation: occupied, standby, unoccupied, open window, frost protection, smoke control, fan fail, summer/winter change over
Obligatory inputs: 1 temperature input for CentraLine wall module
Optional inputs: configurable with COACH:
1 digital input configurable for: window or occupancy or or movement or change over or airflow
1 digital input for window contact
Stand-alone operation: yes
Network operation: yes
Bus system: LonWorks(R)
LonMark(R) profile: 8020
Use COACH software from CentraLine to select the right control software for the required installation.


Power supply: 24Vac
Re-heat output: yes
Triac outputs 24Vac: 4x for heat/cool
Triac outputs 230Vac: no
Auxiliary output signal: no
Note: no


CLSE2L230

Centraline Zone controller, SERVAL

Room temperature controller for 2- and 4-pipe fan coil units, radiators, floorheating and chilled ceiling.
For heater, cooler, electric re-heat and 1,2,3-speed fans.
Heating output signal: triacs (500 mA) configurable for thermal, 3-pt or PWM control
Cooling output signal: triacs (500 mA) configurable for thermal or 3-pt control
Fan output signal: 3 relays (250V~, 3A)
Re-heat output signal: relay (250V~, 10A) (6A UL916)
Control functions: heat only, cool only, heat/cool change over, heat and cool in sequence; in addition electrical reheat; zero energy band
Modes of operation: occupied, standby, unoccupied, open window, frost protection, smoke control, fan fail, summer/winter change over
Obligatory inputs: 1 temperature input for CentraLine wall module
Optional inputs: configurable with COACH:
1 digital input configurable for: window or occupancy or or movement or change over or airflow
1 digital input for window contact
Stand-alone operation: yes
Network operation: yes
Bus system: LonWorks(R)
LonMark(R) profile: 8020
Use COACH software from CentraLine to select the right control software for the required installation.


Power supply: 230Vac
Re-heat output: yes
Triac outputs 24Vac: no
Triac outputs 230Vac: 4x for heat/cool
Auxiliary output signal: AO variable speed fan
Note: no


CLSE2L24

Centraline Zone controller, SERVAL

Room temperature controller for 2- and 4-pipe fan coil units, radiators, floorheating and chilled ceiling.
For heater, cooler, electric re-heat and 1,2,3-speed fans.
Heating output signal: triacs (500 mA) configurable for thermal, 3-pt or PWM control
Cooling output signal: triacs (500 mA) configurable for thermal or 3-pt control
Fan output signal: 3 relays (250V~, 3A)
Re-heat output signal: relay (250V~, 10A) (6A UL916)
Control functions: heat only, cool only, heat/cool change over, heat and cool in sequence; in addition electrical reheat; zero energy band
Modes of operation: occupied, standby, unoccupied, open window, frost protection, smoke control, fan fail, summer/winter change over
Obligatory inputs: 1 temperature input for CentraLine wall module
Optional inputs: configurable with COACH:
1 digital input configurable for: window or occupancy or or movement or change over or airflow
1 digital input for window contact
Stand-alone operation: yes
Network operation: yes
Bus system: LonWorks(R)
LonMark(R) profile: 8020
Use COACH software from CentraLine to select the right control software for the required installation.


Power supply: 230Vac
Re-heat output: yes
Triac outputs 24Vac: 4x for heat/cool
Triac outputs 230Vac: no
Auxiliary output signal: AO variable speed fan
Note: Aux. supply field devices


CLSE3L230

Centraline Zone controller, SERVAL

Room temperature controller for 2- and 4-pipe fan coil units, radiators, floorheating and chilled ceiling.
For heater, cooler, electric re-heat and 1,2,3-speed fans.
Heating output signal: triacs (500 mA) configurable for thermal, 3-pt or PWM control
Cooling output signal: triacs (500 mA) configurable for thermal or 3-pt control
Fan output signal: 3 relays (250V~, 3A)
Re-heat output signal: relay (250V~, 10A) (6A UL916)
Control functions: heat only, cool only, heat/cool change over, heat and cool in sequence; in addition electrical reheat; zero energy band
Modes of operation: occupied, standby, unoccupied, open window, frost protection, smoke control, fan fail, summer/winter change over
Obligatory inputs: 1 temperature input for CentraLine wall module
Optional inputs: configurable with COACH:
1 digital input configurable for: window or occupancy or or movement or change over or airflow
1 digital input for window contact
Stand-alone operation: yes
Network operation: yes
Bus system: LonWorks(R)
LonMark(R) profile: 8020
Use COACH software from CentraLine to select the right control software for the required installation.


Power supply: 230Vac
Re-heat output: no
Triac outputs 24Vac: no
Triac outputs 230Vac: 2x for heat/cool, thermal control only
Auxiliary output signal: no
Note: no


COMP-IP21-KIT1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit for SmartDrive HVAC232/402, size MI1
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-IP21-KIT2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit for SmartDrive HVAC232/402, size MI2
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-IP21-KIT3

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit for SmartDrive HVAC232/402, size MI3
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-LOADER

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive PC connection tools and cables
Product description: SmartDrive Compact Parameter download/upload and PC interface tool with cable for USB connection to PC
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-LOADER-NC

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive PC connection tools and cables
Product description: SmartDrive Compact Parameter download/upload and PC interface tool without cable
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-NEMA1-KIT1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit with additional wiring terminal cover for SmartDrive HVAC232/402, size MI1
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-NEMA1-KIT2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit with additional wiring terminal cover for SmartDrive HVAC232/402, size MI2
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


COMP-NEMA1-KIT3

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 IP20 to IP21 upgrade kits
Product description: IP21 enclosure upgrade kit with additional wiring terminal cover for SmartDrive HVAC232/402, size MI3
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


CONTROL-BOARD1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Control Spares
Product description: Control box and boards for HVAC400 drives
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


CRT12

Centraline Transformer

Protection class: IP00
Input voltage: 220/230 V selectable, 50Hz
Output voltage: 24Vac
With mains fuse. VDE0551 mark.


Model: 288 VA


CRT2

Centraline Transformer

Protection class: IP00
Input voltage: 220/230 V selectable, 50Hz
Output voltage: 24Vac
With mains fuse. VDE0551 mark.


Model: 48 VA


CRT6

Centraline Transformer

Protection class: IP00
Input voltage: 220/230 V selectable, 50Hz
Output voltage: 24Vac
With mains fuse. VDE0551 mark.


Model: 144 VA


CRT6-12

Centraline Transformer, 2 secondary windings

Protection class: IP00
Input voltage: 230 V, 50Hz
Output voltage: 2 x 24Vac, separated
With mains fuse. VDE0551 mark.


Model: 150/250 VA


CRT6-6

Centraline Transformer, 2 secondary windings

Protection class: IP00
Input voltage: 230 V, 50Hz
Output voltage: 2 x 24Vac, separated
With mains fuse. VDE0551 mark.


Model: 144/144 VA


DCPSU-24-1.3

Centraline DC Power Supply

Single phase switched power supply 24 Vdc
Output short circuit protection
DIN rail mounting
2 x 24 V push in terminals
Voltage adjustment


Product description: DC Power Supply 1,3A


DCPSU-24-2.5

Centraline DC Power Supply

Single phase switched power supply 24 Vdc
Output short circuit protection
DIN rail mounting
2 x 24 V push in terminals
Voltage adjustment


Product description: DC Power Supply 2,5A


DCPSU-24-4

Centraline DC Power Supply

Single phase switched power supply 24 Vdc
Output short circuit protection
DIN rail mounting
2 x 24 V push in terminals
Voltage adjustment


Product description: DC Power Supply 4A


DPS1000

Centraline Differential pressure switch for air (DPS)

Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa


Pressure adjustment range: 200...1000Pa
Switching differential: 1mbar


DPS200

Centraline Differential pressure switch for air (DPS)

Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa


Pressure adjustment range: 20...200Pa
Switching differential: 0.1mbar


DPS2500

Centraline Differential pressure switch for air (DPS)

Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa


Pressure adjustment range: 500...2500Pa
Switching differential: 1.5mbar


DPS400

Centraline Differential pressure switch for air (DPS)

Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa


Pressure adjustment range: 40...400Pa
Switching differential: 0.2mbar


DPS500

Centraline Differential pressure switch for air (DPS)

Filter monitor or flow switch for air, non-combustible, non aggressive gases in air conditioning and ventilating installations.
Kind of pressure: overpressure, relative
Pressure connection: plastic connection piece for 5 mm (internal) hose
Electrical connection: AMP connector 6,3x0,8 (DIN 46244) or screw terminals
Protection class: IP54
Sensing element material: ABS + Silicon
Media temp.: -20...85C
Ambient temperature: -20...85C
Switch function/capacity: SPDT switch 240 Vac; 1,5 A (0.4)A
Certificates: CE0085AR0013 according EC Gas Appliance Directive EU/2009/142/EG and DIN EN 1854
Accessories supplied with pressure switch: 2 m silicon hose, 2 connection pieces with mounting screws, 2 self tapping screws for mounting on housing, 3 screw terminals for electrical connection.
Max. pressure: 10kPa


Pressure adjustment range: 50...500Pa
Switching differential: 0.2mbar


DPSK

Centraline Differential pressure transmitter for air (DPTE)
Accessories

Duct Kit, including 2m silicone-hose and 2 joining pipes DPSJ with screws



DPSL

Centraline Differential pressure transmitter for air (DPTE)
Accessories

Mounting brackets L-shaped



DPTE100

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...100/250Pa
Max. pressure: 20kPa


DPTE1000

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...1000/2500Pa
Max. pressure: 40kPa


DPTE1000D

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: 0...1000/2500Pa
Max. pressure: 40kPa


DPTE1000S

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -1000...1000Pa
Max. pressure: 20kPa


DPTE1000SD

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: -1000...1000Pa
Max. pressure: 20kPa


DPTE1002

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...1000/2500Pa
Max. pressure: 40kPa


DPTE100D

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: 0...100/250Pa
Max. pressure: 20kPa


DPTE100S

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -100...100Pa
Max. pressure: 20kPa


DPTE100SD

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: -100...100Pa
Max. pressure: 20kPa


DPTE102

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...100/250Pa
Max. pressure: 20kPa


DPTE102S

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: -100...100Pa
Max. pressure: 20kPa


DPTE250

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...250/500Pa
Max. pressure: 20kPa


DPTE250D

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: 0...250/500Pa
Max. pressure: 20kPa


DPTE252

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...250/500Pa
Max. pressure: 20kPa


DPTE500

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...500/1000Pa
Max. pressure: 20kPa


DPTE5000

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: 0...5000/10000Pa
Max. pressure: 60kPa


DPTE5000D

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: 0...5000/10000Pa
Max. pressure: 60kPa


DPTE5002

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...5000/10000Pa
Max. pressure: 60kPa


DPTE500D

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: 0...500/1000Pa
Max. pressure: 20kPa


DPTE500S

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -500...500Pa
Max. pressure: 20kPa


DPTE500SD

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: -500...500Pa
Max. pressure: 20kPa


DPTE502

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: 0...500/1000Pa
Max. pressure: 20kPa


DPTE50S

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V/4 - 20 mA, analog output, supply voltage 18...30 Vac/dc, 50/60 Hz
Pressure range: -50...50Pa
Max. pressure: 20kPa


DPTE50SD

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

3-wire models, selectable 0 - 10 V / 4 - 20 mA analog output, supply voltage 18...30 Vac/dc, 50/60 Hz; WITH LED Display
Pressure range: -50...50Pa
Max. pressure: 20kPa


DPTE52S

Centraline Differential pressure transmitter for air (DPTE)

Differential pressure transmitter for air-conditioning/ventilation.
Air-conditioning and ventilation systems, Building automation, Environmental protection, Fan and ventilation control, Valve and shutter control, Filter and fan monitoring
Kind of pressure: differential pressure, relative
Pressure connection: 6mm hose pipe
Electrical connection: M20x1,5
Protection class: IP54
Housing material: ABS and POM
Sensing method: piezoresistive
Sensing element material: ABS + POM
Media temp.: 0...50C
Medium: gaseous
Ambient temperature: 0...50C
Duct Kit DPSK included in delivery of single package.
Adjustable by jumper to the next higher pressure range.
Factory settings: see column "pressure range". Full scale pressure range see data sheet

2-wire models, analog output 4 - 20 mA, supply voltage 16 ... 32 Vdc
Pressure range: -50...50Pa
Max. pressure: 20kPa


DR100GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 100mm
Kvs value: 160
Max. delta P: 100kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 30Nm
Port connection: flanges DIN2531


DR125GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 125mm
Kvs value: 250
Max. delta P: 70kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 30Nm
Port connection: flanges DIN2531


DR15-2GMLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Internal threads
DN size: 15mm
Kvs value: 2.5
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads


DR150GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 150mm
Kvs value: 630
Max. delta P: 50kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 40Nm
Port connection: flanges DIN2531


DR15GMLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Internal threads
DN size: 15mm
Kvs value: 4
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads


DR200GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 200mm
Kvs value: 1600
Max. delta P: 50kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 40Nm
Port connection: flanges DIN2531


DR200GFLA1

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 200mm
Kvs value: 1000
Max. delta P: 50kPa
Torque for max. delta P: 40Nm
Torque for reduced delta P: 40Nm
Port connection: flanges DIN2531


DR20GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 20mm
Kvs value: 6.3
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DR20GMLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Internal threads
DN size: 20mm
Kvs value: 6.3
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads


DR25GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 25mm
Kvs value: 10
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DR25GMLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Internal threads
DN size: 25mm
Kvs value: 10
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads


DR32GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 32mm
Kvs value: 16
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DR32GMLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Internal threads
DN size: 32mm
Kvs value: 16
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads


DR40GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 40mm
Kvs value: 25
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DR40GMLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Internal threads
DN size: 40mm
Kvs value: 25
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: internal threads


DR50GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 50mm
Kvs value: 40
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DR65GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 65mm
Kvs value: 63
Max. delta P: 100kPa
Torque for max. delta P: 20Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DR80GFLA

Centraline Three-way rotary valve PN6

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRG
Valve type: 3-way rotary mixing
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN6
Reduced delta P: 40kPa

Flanges
DN size: 80mm
Kvs value: 100
Max. delta P: 100kPa
Torque for max. delta P: 30Nm
Torque for reduced delta P: 20Nm
Port connection: flanges DIN2531


DRA-02L

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Display panel kits
Product description: NXL door installation set for display panel, 2m cable
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


DRA-04B

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Display panel kits
Product description: NXS door installation set for display panel, 4m cable
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


DRA-04L

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Display panel kits
Product description: NXL door installation set for display panel, 4m cable
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


DRA02B

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Display panel kits
Product description: NXS door installation set for display panel, 2m cable
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


DRU25-10

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 25mm
Kvs value: 10


DRU25-16

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 25mm
Kvs value: 16


DRU25-2.5

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 25mm
Kvs value: 2.5


DRU25-4.0

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 25mm
Kvs value: 4


DRU25-6.3

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 25mm
Kvs value: 6.3


DRU32-10

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 32mm
Kvs value: 10


DRU32-16

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 32mm
Kvs value: 16


DRU32-25

Centraline Three-way rotary valve PN10

For supply water, heating and air conditioning; hot/cold water quality VDI2035; glycol water mixture 50%.
Valve series: DRU
Valve type: 3-way rotary mixing, bypass
Medium type: water
Materials: body cast iron, inner parts chrome plated
Packing: double O-ring sealing
Angle of rotation: 90o
Media temp.: 2...130C
Nominal pressure: PN10
Port connection: external threads
Max. delta P: 100kPa
Torque for max. delta P: 20Nm

Universal Rotary Valve
DN size: 32mm
Kvs value: 25


EEM230-D-M

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication


Interface: M-Bus
Certificates: no


EEM230-D-M-MID

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication


Interface: M-Bus
Certificates: MID


EEM230-D-MO

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication


Interface: ModBus RTU
Certificates: no


EEM230-D-MO-MID

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication


Interface: ModBus RTU
Certificates: MID


EEM230-D-P

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication


Interface: pulse
Certificates: no


EEM230-D-P-MID

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage, active and reactive power.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy
Resettable value of partial energy
Display of instantaneous power
Reactive power available through interface
Display of voltage
Display of current
Clear fault indication


Interface: pulse
Certificates: MID


EEM230-E-P

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, Economic, EEM230-E

Energy meter with LCD display and integrated S0 interface. The S0 interface is a hardware interface for the transmission of measured values in building automation.
Single phase energy meter, 230VAC 50 Hz
Direct measurement up to 32 A
7-digit LC-Display
Lead seal possible with cap as accessory
Precision class 1 according to IEC62053-21
S0 output according to IEC62053-31
Clear fault indication
Interface: pulse


EEM230-SEALCAP

Centraline Electrical Energy Meters, 1 phase, 32A, LCD, EEM230-D


20 sealcaps (for 10 energy meters)



EEM400-D-M

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: M-Bus
Certificates: no


EEM400-D-M-MID

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: M-Bus
Certificates: MID


EEM400-D-MO

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: ModBus RTU
Certificates: no


EEM400-D-MO-MID

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: ModBus RTU
Certificates: MID


EEM400-D-P

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: pulse
Certificates: no


EEM400-D-P-MID

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Direct measurement up to 65 A
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
2 tariff measuring
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: pulse
Certificates: MID


EEM400-SEALCAP

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D


20 sealcaps (for 5 energy meters)



EEM400C-D-M

Centraline Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: M-Bus
Certificates: no


EEM400C-D-M-MID

Centraline Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: M-Bus
Certificates: MID


EEM400C-D-MO

Centraline Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: ModBus RTU
Certificates: no


EEM400C-D-MO-MID

Centraline Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: ModBus RTU
Certificates: MID


EEM400C-D-P

Centraline Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: pulse
Certificates: no


EEM400C-D-P-MID

Centraline Electrical Energy Meters, 3 phases for current transformer 5A, LCD, EEM400C-D

Electrical energy meter with direct reading of all relevant data, such as energy (total and partial), current and voltage for every phase and active and reactive power for every phase and for the three phases.
3-phase energy meter, 3 x 230/400 VAC 50 Hz
Measurement up to 1.500 A over external current transformer
Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
7-digits display, clear read-out with 6 mm tall figures
Backlighted LCD
Metering of total and partial consumed energy, partial resettable
CT ratio is blocked through a wire bridge
Display of instantaneous power for each phase and all phases
Display of voltage of each phase
Display of current
Reactive power for every and/or all phases available through interface
Energy value readable without power supply
Clear fault indication


Interface: pulse
Certificates: MID


ENC-Slot-MI1-MI3

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: Required external cover to fix option boards on HVAC232/402 frame size 1..3 for devices up to 5,5 kW
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


ENC-Slot-MI4-MI5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: Required internal moulding to fix option boards on HVAC232/402 frame size 4..5 for devices bigger than 5,5 kW
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


EVA1-DANFOSS

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Adapters

Danfoss-RA adapter



FT6960-18

Centraline Single-stage frost protection thermostat (FT69)

Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65


Temperature element: capillary with bulb
Capillary tube length: 1.8m
Mechanical lock/reset: manual


FT6960-30

Centraline Single-stage frost protection thermostat (FT69)

Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65


Temperature element: capillary
Capillary tube length: 3m
Mechanical lock/reset: manual


FT6960-60

Centraline Single-stage frost protection thermostat (FT69)

Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65


Temperature element: capillary
Capillary tube length: 6m
Mechanical lock/reset: manual


FT6961-18

Centraline Single-stage frost protection thermostat (FT69)

Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65


Temperature element: capillary with bulb
Capillary tube length: 1.8m
Mechanical lock/reset: automatic


FT6961-30

Centraline Single-stage frost protection thermostat (FT69)

Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65


Temperature element: capillary
Capillary tube length: 3m
Mechanical lock/reset: automatic


FT6961-60

Centraline Single-stage frost protection thermostat (FT69)

Suitable for use as frost-protection thermostats for the protection of downstream air heaters in ventilation and climate control systems as well as heat exchangers in cooling systems. Can also be used to control electrical heating systems and to switch acoustic or optical alarm signals.
Housing material: Polycarbonate and ABS
Ambient temperature: -20...55C
Switch function/capacity: SPDT 24..250 Vac, 15(8)A
Thermostat application: frost protection thermostat
Protection class: IP65


Temperature element: capillary
Capillary tube length: 6m
Mechanical lock/reset: automatic


H7012A1010

Centraline Room R.H.- and temperature sensor

Combined Room Humidity and Temperature Sensor with various sensor elements
Approvals: IEC751 class B for Pt1000 sensor
Protection class: IP30
R.H. range: 5...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 130mm|80mm|34mm


Temperature element: no
Output signal: no
Temperature range: no


H7012B1008

Centraline Room R.H.- and temperature sensor

Combined Room Humidity and Temperature Sensor with various sensor elements
Approvals: IEC751 class B for Pt1000 sensor
Protection class: IP30
R.H. range: 5...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 130mm|80mm|34mm


Temperature element: Pt1000
Output signal: no
Temperature range: 0...50C


H7012B1024

Centraline Room R.H.- and temperature sensor

Combined Room Humidity and Temperature Sensor with various sensor elements
Approvals: IEC751 class B for Pt1000 sensor
Protection class: IP30
R.H. range: 5...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 130mm|80mm|34mm


Temperature element: NTC20k
Output signal: no
Temperature range: 0...50C


H7012B1030

Centraline Room R.H.- and temperature sensor

Combined Room Humidity and Temperature Sensor with various sensor elements
Approvals: IEC751 class B for Pt1000 sensor
Protection class: IP30
R.H. range: 5...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 130mm|80mm|34mm


Temperature element: no
Output signal: temp: 0..10V=
Temperature range: 0...50C


H7508B1060

Centraline Outdoor R.H.- and temperature sensor/transmitter

Protection class: IP34
Relative humidity sensor accuracy class: 3%.
Temperature range: -30...50C
R.H. range: 5...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vacdc
Mounting place: wall outside
Housing (HxWxD): 172mm|132mm|60mm


Temperature element: no
Output signal: temp: 0..10V=
Wiring terminals: 5


H7508B1080

Centraline Outdoor R.H.- and temperature sensor/transmitter

Protection class: IP34
Relative humidity sensor accuracy class: 3%.
Temperature range: -30...50C
R.H. range: 5...95%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Power supply: 24Vacdc
Mounting place: wall outside
Housing (HxWxD): 172mm|132mm|60mm


Temperature element: NTC20k
Output signal: no
Wiring terminals: 6


HCA1VEL

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Adapters

Mounting adapter for Velta -Compact Manifold



HE25

Centraline Three-way rotary valve PN10
H-extensions

H-extension DN25



HE32

Centraline Three-way rotary valve PN10
H-extensions

H-extension DN32



HGK3

Centraline Air duct humidistat

Line voltage immersion humidistat for air ducts or industrial areas.
Switch function/capacity: SPDT 230 Vac, 15 A
R.H. setpoint range: 35...100%rh
R.H. hysteresis switching point: 4%rh
Ambient temperature: -30...60C
R.H. sensing element: plastic tissue
(De) Humidification application: D + H
Mounting place: air duct


HON-NX8-KIT

Centraline Connected Building Management, HAWK 8000
HAWK 8000 Spare parts

HAWK 8000 WIFI-antenna, RS485 terminals, and power terminals



HON-NXEM-232

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 Expansion modules
Product description: RS232 EXPANSION MODULE SINGLE PORT


HON-NXEM-2X485

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 Expansion modules
Product description: RS385 EXPANSION MODULE DUAL PORT


HON-NXEM-LON

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 Expansion modules
Product description: LON EXPANSION MODULE SINGLE PORT


HSS-DPS

Centraline Dew-point switch

This early-warning dew-point switch is designed for use in monitoring cooling water pipes or chilled surfaces in order to determine if temperatures are approaching the dewpoint. It is suitable for mounting on flat and round surfaces. The switch measures the relative humidity prevailing directly at the chilled surface and can thus be used to:
regulating cooling performance
switching cooling systems ON and OFF
signalling if the temperature is approaching the dew-point
Status indication with LED, showing condensation danger
Switching point at 90 %rh, hysteresis 5 %rh
Ambient temperature: 0...50C
Protection class: IP40
Mounting: wall, duct or pipe (max. 50 mm)
Power supply: 24Vacdc
Switch function/capacity: potential free changeover contact; max. 24 Vac/dc, 1 A
Wiring connection: 5-pole push-in terminals, max. 1,5mm2


HVAC-DOOR-KIT

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Display panel kits
Product description: SmartDrive HVAC door installation set for display panel, 3m cable
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 4 (HVAC400-1P1..HVAC400-5P5)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 5 (HVAC400-7P5..HVAC400-15P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-6

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 6 (HVAC400-18P..HVAC400-30P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-7

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 7 (HVAC400-37P..HVAC400-55P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-8

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 8 (HVAC400-75P..HVAC400-110P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-9

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: SmartDrive HVAC spare part fan size 9 (HVAC400-132P..HVAC400-160P)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-SUP-FR08

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, power supply, frame size 8, HVAC400-75Px - HVAC400-110x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-FAN-SUP-FR09

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, power supply, frame size 9, HVAC400-132x - HVAC400-160x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-HMI-A

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive HVAC display panels
Product description: SmartDrive HVAC advanced commissioning display/keypad with parameter copy function
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-IP54FAN-FR04

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 4, HVAC400-1P1x - HVAC400-5P5x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-IP54FAN-FR05

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 5, HVAC400-7P5x - HVAC400-15Px
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-IP54FAN-FR06

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 6, HVAC400-18Px - HVAC400-55Px
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-IP54FAN-FR08

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 8, HVAC400-75Px - HVAC400-110x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-IP54FAN-FR09

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC400 Cooling Fans
Product description: HVAC400, Internal fan, frame size 9, HVAC400-132x - HVAC400-160x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC-TERM-KIT

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Control Spares
Product description: Kit of terminal for HVAC400x drives
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


HVAC03C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 1.1kW
Low overload Icont: 3.3A
High overload (for Machines): 0.75kW
High overload Icont: 2.2A


HVAC04C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 1.5kW
Low overload Icont: 4.3A
High overload (for Machines): 1.1kW
High overload Icont: 3.3A


HVAC05C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 2.2kW
Low overload Icont: 5.6A
High overload (for Machines): 1.5kW
High overload Icont: 4.3A


HVAC07C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 3kW
Low overload Icont: 7.6A
High overload (for Machines): 2.2kW
High overload Icont: 5.6A


HVAC09C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 4kW
Low overload Icont: 9A
High overload (for Machines): 3kW
High overload Icont: 7.6A


HVAC12C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 5.5kW
Low overload Icont: 12A
High overload (for Machines): 4kW
High overload Icont: 9A


HVAC16C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 7.5kW
Low overload Icont: 16A
High overload (for Machines): 5.5kW
High overload Icont: 12A


HVAC232-1P1-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Power: 1.1kW
Low overload Icont: 4.8A
Size: 2


HVAC232-1P5-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Power: 1.5kW
Low overload Icont: 7A
Size: 2


HVAC232-2P2-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Power: 2.2kW
Low overload Icont: 9.6A
Size: 3


HVAC232-P37-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Power: 0.37kW
Low overload Icont: 2.4A
Size: 1


HVAC232-P55-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Power: 0.55kW
Low overload Icont: 2.8A
Size: 1


HVAC232-P75-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

230V series
Protection class: IP20
Voltage: 230V
1 phase input: yes
3 phases input: no
Power: 0.75kW
Low overload Icont: 3.7A
Size: 2


HVAC23C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 11kW
Low overload Icont: 23A
High overload (for Machines): 7.5kW
High overload Icont: 16A


HVAC31C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 15kW
Low overload Icont: 31A
High overload (for Machines): 11kW
High overload Icont: 23A


HVAC38C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 18.5kW
Low overload Icont: 38A
High overload (for Machines): 15kW
High overload Icont: 31A


HVAC400-110-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 110kW
Low overload Icont: 205A
Size: 8


HVAC400-110-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 110kW
Low overload Icont: 205A
Size: 8


HVAC400-11P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 11kW
Low overload Icont: 23A
Size: 5


HVAC400-11P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 11kW
Low overload Icont: 23A
Size: 5


HVAC400-132-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 132kW
Low overload Icont: 261A
Size: 9


HVAC400-132-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 132kW
Low overload Icont: 261A
Size: 9


HVAC400-15P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 15kW
Low overload Icont: 31A
Size: 5


HVAC400-15P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 15kW
Low overload Icont: 31A
Size: 5


HVAC400-160-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 160kW
Low overload Icont: 310A
Size: 9


HVAC400-160-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 160kW
Low overload Icont: 310A
Size: 9


HVAC400-18P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 18.5kW
Low overload Icont: 38A
Size: 6


HVAC400-18P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 18.5kW
Low overload Icont: 38A
Size: 6


HVAC400-1P1-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 1.1kW
Low overload Icont: 3.4A
Size: 4


HVAC400-1P1-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 1.1kW
Low overload Icont: 3.4A
Size: 4


HVAC400-1P5-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 1.5kW
Low overload Icont: 4.8A
Size: 4


HVAC400-1P5-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 1.5kW
Low overload Icont: 4.8A
Size: 4


HVAC400-22P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 22kW
Low overload Icont: 46A
Size: 6


HVAC400-22P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 22kW
Low overload Icont: 46A
Size: 6


HVAC400-2P2-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 2.2kW
Low overload Icont: 5.6A
Size: 4


HVAC400-2P2-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 2.2kW
Low overload Icont: 5.6A
Size: 4


HVAC400-30P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 30kW
Low overload Icont: 61A
Size: 6


HVAC400-30P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 30kW
Low overload Icont: 61A
Size: 6


HVAC400-37P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 37kW
Low overload Icont: 72A
Size: 7


HVAC400-37P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 37kW
Low overload Icont: 72A
Size: 7


HVAC400-3P0-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 3kW
Low overload Icont: 8A
Size: 4


HVAC400-3P0-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 3kW
Low overload Icont: 8A
Size: 4


HVAC400-45P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 45kW
Low overload Icont: 87A
Size: 7


HVAC400-45P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 45kW
Low overload Icont: 87A
Size: 7


HVAC400-4P0-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 4kW
Low overload Icont: 9.6A
Size: 4


HVAC400-4P0-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 4kW
Low overload Icont: 9.6A
Size: 4


HVAC400-55P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 55kW
Low overload Icont: 105A
Size: 7


HVAC400-55P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 55kW
Low overload Icont: 105A
Size: 7


HVAC400-5P5-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 5.5kW
Low overload Icont: 12A
Size: 4


HVAC400-5P5-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 5.5kW
Low overload Icont: 12A
Size: 4


HVAC400-75P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 75kW
Low overload Icont: 140A
Size: 8


HVAC400-75P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 75kW
Low overload Icont: 140A
Size: 8


HVAC400-7P5-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 7.5kW
Low overload Icont: 16A
Size: 5


HVAC400-7P5-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 7.5kW
Low overload Icont: 16A
Size: 5


HVAC400-90P-21A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21
Protection class: IP21
Power: 90kW
Low overload Icont: 170A
Size: 8


HVAC400-90P-54A

Centraline Inverters 1,1..160kW, IP21/IP54, SmartDrive HVAC

Variable speed drives for induction- and permanent magnet motors, with built-in RFI filters. EMC and LVD compliant.
The SmartDrive HVAC inverters are especially designed with many advanced features for Heating, ventilation and air-conditioning applications.
Features: Detachable multilanguage HMI with advanced commissioning display/keypad (parameter copy function)
Compact size
Integrated stress removal and 360o grounding for power cable shield inside the device no need for cable glands
Varnished circuit boards as standard
Real Time Clock for timed functions and fault time stamps
Inputs/Outputs: 2 analog inputs (mA/V), 6 digital inputs, 2 relays (NO/NC), 1 thermistor input (PTC), 1 analog output (mA/V), Ethernet (IP), RS485 (MS/TP)
Flexible I/O configuration: 2 free slots for expansion boards
Start Up wizard for extremely fast start of basic pump and fan applications
Mini wizards for more advanced applications: PID, Cascade Control and Resonance sweep wizards
Intelligent automatic functionality: Ramp Time Optimizer, Overtemperature ride-through, Power ride-through etc.
PID controller with advanced features: Sleep mode, Pump Soft fill, pressure loss compensation, Cascade controller etc.
U/f control
Series: SmartDrive HVAC
RFI-filter: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Standard: BACnet IP, Modbus TCP/IP, BACnet MS/TP, Modbus RTU, N2. Optional: LonWorks
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
EN61800-3, category C1 with optional filters Type: RFI.. (see Accessories)
EN61000-3-12
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54
Protection class: IP54
Power: 90kW
Low overload Icont: 170A
Size: 8


HVAC402-11P-21

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 11kW
Low overload Icont: 23A
Size: 4


HVAC402-15P-21

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 15kW
Low overload Icont: 31A
Size: 5


HVAC402-18P-21

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 18.5kW
Low overload Icont: 38A
Size: 5


HVAC402-1P1-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 1.1kW
Low overload Icont: 3.3A
Size: 2


HVAC402-1P5-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 1.5kW
Low overload Icont: 4.3A
Size: 2


HVAC402-2P2-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 2.2kW
Low overload Icont: 5.6A
Size: 2


HVAC402-3P0-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 3kW
Low overload Icont: 7.6A
Size: 3


HVAC402-4P0-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 4kW
Low overload Icont: 9A
Size: 3


HVAC402-5P5-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 5.5kW
Low overload Icont: 12A
Size: 3


HVAC402-7P5-21

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP21
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 7.5kW
Low overload Icont: 16A
Size: 4


HVAC402-FAN-FR4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 Cooling Fans
Product description: HVAC402, main fan, size 4, HVAC402-7P5-21 - HVAC402-11P-21
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


HVAC402-FAN-FR5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

HVAC232/402 Cooling Fans
Product description: HVAC402, main fan, size 5, HVAC402-15P-21 - HVAC402-18P-21
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


HVAC402-P55-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 0.55kW
Low overload Icont: 1.9A
Size: 1


HVAC402-P75-20

Centraline Inverters 0,37..18,5kW, IP20/IP21, HVAC232/402

Variable frequency drives for induction and permanent magnet motors. Compliant with EMC and LVD. HVAC232 and HVAC402 are compact in size and flexible in application with one free slot for an option board. Easy to operate and commissioning with an embedded wizard.
Torque characteristics can be adjusted to square for pumps and fans or to constant for machines in industrial or process operation.
Features: Start up wizard
Embedded soft-filling-and sleep function
Configurable inputs and outputs: 2 analog inputs (voltage or current), 6 digital inputs, 3 digital outputs (2 relays, 1 open collector), 1 analog output (mA)
Series: HVAC232/402
RFI-filter: integrated
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3, category C2
Safety: EN61800-5, CE

400V series
Protection class: IP20
Voltage: 400V
1 phase input: no
3 phases input: yes
Power: 0.75kW
Low overload Icont: 2.4A
Size: 1


HVAC46C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 22kW
Low overload Icont: 46A
High overload (for Machines): 18.5kW
High overload Icont: 38A


HVAC61C5

Centraline Inverters 1,1..30kW, IP54, NXL HVAC

Variable speed drives for induction motors, with built-in RFI filters. EMC and LVD compliant.
The inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload ratings are used. Industrial or process installations normally require High Overload ratings.
Features: the software is tailored to meet the typical HVAC application
start-up wizard
optimized I/O configuration including thermistor input
flexible I/O configuration: 2 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 thermistor input, 1 analog output
Series: NXL HVAC
RFI-filter: integrated
Brake chopper: integrated
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: Modbus RTU as standard; optional: LonWorks, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Emissions: EN61800-3 (IP21: category C2, IP54: category C1)
Safety: EN61800-5, CE, UL, cUL
http://hwll.co/inverter
1 phase input: no
3 phases input: yes
Protection class: IP54

IP54
Power: 30kW
Low overload Icont: 61A
High overload (for Machines): 22kW
High overload Icont: 46A


HVACDOORKIT

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Display panel kits
Product description: HVAC232/402 door installation set including 2m cable and display
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


IF-LON2

Centraline C-Bus interfaces

C-Bus Interfaces


Product description: High performance external LON-USB interface adapter. For EAGLE, EAGLEHAWK and CLIF-CBUSLC.


IRA-AD

Centraline Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A
Accessories

Adapter for Danfoss RA2000



IRM-RLC

Centraline Configurable BACnet room controller MERLIN
Cover

Terminal cover IP30 for Large housing (10 pieces)



IRM-RSC

Centraline Configurable BACnet room controller MERLIN
Cover

Terminal cover IP30 for Small housing (10 pieces)



KSW230

Centraline Electronic flow switches for liquid, compact version (KSW)

The high reliable compact electronic flow switch is designed for detecting water flow in pipes. As soon as medium flow speed exceeds or falls under a customer adjusted value, the device will switch a electric circuit.
Protection class: IP65
Switch function/capacity: SPDT, capacity 250 Vac, 10(2) A
LED's available for indication of power supply and switch status.
Immersion depth: 20mm
Media: liquid and air
Setpoint range: 0,05..3 m/s
Max. media temperature: 80C
Max. pressure: 30bar

Process connection G1/2"
Power supply: 230Vac


KSW24

Centraline Electronic flow switches for liquid, compact version (KSW)

The high reliable compact electronic flow switch is designed for detecting water flow in pipes. As soon as medium flow speed exceeds or falls under a customer adjusted value, the device will switch a electric circuit.
Protection class: IP65
Switch function/capacity: SPDT, capacity 250 Vac, 10(2) A
LED's available for indication of power supply and switch status.
Immersion depth: 20mm
Media: liquid and air
Setpoint range: 0,05..3 m/s
Max. media temperature: 80C
Max. pressure: 30bar

Process connection G1/2"
Power supply: 24Vac


KTF00-65-2M

Centraline Water temperature sensor Pt1000, cable type

Approvals: IEC751 class B
Protection class: IP65
Temperature element: Pt1000
Mounting place: universal
Immersion depth: min. 50mm
Sensing element (dia x L): 6mm|50mm


Temperature range: -30...105C
Cable length: 2m
Packing unit quantity: 1


KTF00-65-2M-300

Centraline Water temperature sensor Pt1000, cable type

Approvals: IEC751 class B
Protection class: IP65
Temperature element: Pt1000
Mounting place: universal
Immersion depth: min. 50mm
Sensing element (dia x L): 6mm|50mm


Temperature range: -20...260C
Cable length: PFTE, 2m
Packing unit quantity: 1


KTF00-65-2M-B

Centraline Water temperature sensor Pt1000, cable type

Approvals: IEC751 class B
Protection class: IP65
Temperature element: Pt1000
Mounting place: universal
Immersion depth: min. 50mm
Sensing element (dia x L): 6mm|50mm


Temperature range: -30...105C
Cable length: 2m
Packing unit quantity: 50


KTF00-65-5M-B

Centraline Water temperature sensor Pt1000, cable type

Approvals: IEC751 class B
Protection class: IP65
Temperature element: Pt1000
Mounting place: universal
Immersion depth: min. 50mm
Sensing element (dia x L): 6mm|50mm


Temperature range: -30...105C
Cable length: 5m
Packing unit quantity: 50


KTF10-65-2M

Centraline Water temperature sensor NTC, cable type

Watertight temperature sensor with sensor cartridge.
Protection class: IP65
Metal immersion spring is not included
Temperature range: -30...105C
Mounting place: universal
Immersion depth: 50mm
Sensing element (dia x L): 6mm|50mm
Wiring terminals: 2
Cable length: 2m


Temperature element: NTC10k


KTF20-65-2M

Centraline Water temperature sensor NTC, cable type

Watertight temperature sensor with sensor cartridge.
Protection class: IP65
Metal immersion spring is not included
Temperature range: -30...105C
Mounting place: universal
Immersion depth: 50mm
Sensing element (dia x L): 6mm|50mm
Wiring terminals: 2
Cable length: 2m


Temperature element: NTC20k


LAS-CLIP-25

Centraline Leakage Alarm System SeaHawk
Accessories

Cable fixations (installation fixation for both the sensing cable and the non-sensing cable (25 pieces)



LAS-NSC7

Centraline Leakage Alarm System SeaHawk
Cables

Non-sensing cable, length 7,6 meter



LAS-PSWA

Centraline Leakage Alarm System SeaHawk
Accessories

Power supply 230 V, 50 Hz / 24 Vdc



LAS-SC15

Centraline Leakage Alarm System SeaHawk
Cables

Sensing cable, length 15,2 meter



LAS-SC30

Centraline Leakage Alarm System SeaHawk
Cables

Sensing cable, length 30,4 meter



LAS-SC7

Centraline Leakage Alarm System SeaHawk
Cables

Sensing cable, length 7,6 meter



LAS-SD-Z

Centraline Leakage Alarm System SeaHawk
Spot detector

Spot detector



LAS-SH10

Centraline Leakage Alarm System SeaHawk

The SeaHawk Leakage Alarm System is a distance-read leak detection supervised system that continuously monitors a length of cable for continuity and leaks. When a cable break, contamination or leak is detected, the module calculates and annunciates the distance to the leak. This distance can then be cross-referenced with a cable reference map or immediately located by accessing an interactive map.
The SeaHawk controller can be applied for standalone operation including detection annunciation display or can be integrated into a building management system via Modbus to the Hawk controller providing a centralized source of monitoring, communication and notification capabilities.
Control software: configurable with COACH-AX software
Hardware inputs: sensing cable for water detection, length 11..3000 m
Output signal: relay SPDT contact 30 Vdc 5 A resistive, 250 Vac 8 A resistive; minimum load 10 mA 5 Vdc (signal)
audible alarm 85 dB(A) at 0,6 m
Display functions: red LED for leak alarm
yellow LED for cable contamination or fault
4-character LED display for distance or fault status
Stand-alone operation: yes
Bus system description: EIA-485, Modbus (RTU)
Mounting: DIN rail, or wall mounting with screws
Protection class: IP30
Type of terminals: screw terminals with terminal block
Power supply: 12..24 Vacdc
Housing (HxWxD): 109mm|71mm|61mm


LAS-WCCS

Centraline Leakage Alarm System SeaHawk
Accessories

Weighted cable connector (simulates 15,2 meter of sensing cable)



LNX-S-1N-200PP

Centraline Web based Supervisor software, ARENA NX

ARENA NX is a web-based building monitoring and management solution build upon the powerful Niagara 4 platform. It is capable of integrating CentraLine BACnet and Niagara controllers, third party devices and internet protocols into a centralized software platform that is designed to manage buildings at an enterprise level. It is used to supervise HVAC systems and non-HVAC systems (e.g. lighting, security, life safety) in a building or across multiple buildings.
ARENA NX serves real time graphical information to standard web-browser clients and also provides server-level functions such as: centralized data logging, archiving, alarming, real time graphical displays, master scheduling, system-wide database management, and integration with enterprise software applications. ARENA NX helps to maximize operating and services opportunities and to minimize associated costs.
The comprehensive graphical engineering tool set (COACH NX) is embedded in the ARENA NX. COACH NX is the single engineering tool for HAWK and ARENA NX.
Features:
WEB ACCESS Access to alarms, graphics, schedules, logs and configuration data with a web browser and mobile devices
REAL TIME GRAPHICAL DISPLAY Free configurable HTML5 user interface. Supported by libraries and template functions for an efficient user interface engineering
ALARMING Sophisticated alarm segregation, processing, escalation and routing, including e-mail alarm acknowledging
CONNECTIVITY BACnet driver with server and client support. C-Bus, Modbus IP, LON IP, MBUS, KNX IP, OPC and SNMP drivers supported by open point license
SCHEDULING Read / write access to BACnet, C-Bus and Niagara schedules. Global schedule and calendar functions Scheduling on Supervisor support to manage device without internal schedule function
CENTRALIZED DATA LOGGING All points can be added to a history database. Interval and Change Of Value (COV) algorithms are supported. History data can be visualized in easy and intuitive way
ENERGYMANAGEMENT Basic energy management functions are included, enhanced features can be added. CentraLine ENERGYVISION is an extension module to the supervisor
AUDIT Audit Trail of database changes, database storage and backup, global time functions, calendar, central scheduling, control and energy management routines
NAVIGATION Navigation can easily be adjusted to End-User permissions and needs
SCRIPTING / LOGIC Freely programmed scripts and logic can be used to implement control and management functions on supervisor level. Batch functions can be executed to force actions or adjust settings across the system
PLANT CONTROLLER SUPPORT Supports multiple HAWK / EAGLEHAWK and EAGLE controllers connected to a local Ethernet network, or the Internet. Remote back up of HAWK applications to Supervisor
CONFIGURABLE ROOM CONTROLLER SUPPORT Supports template for efficient configuration of MERLIN application. BACnet parameter have not to be considered as license points
META DATA SUPPORT(Tagging) Additional information can be added to all integrated objects. Those information can be used to structure data, search data and prepare data for further analytics
DOCUMENTATION Full Supervisor documentation on "one click"
DASHBOARDING Data summary views customizable by End-Users
SEARCH Find data quickly, by using the clear text search function
SECURITY Password protection and security using authentication and encryption techniques with optional security supported via an external LDAP connection
USERS Supports an unlimited number of users via Internet / Intranet access with a standard web browser, depending on the host PC / Server resources
ARCHIVING Optional enterprise-level data archival using SQL and, MySQL database and XML, CSV or text formats
REPORTING Define reports which can be manually or automatically be created as pdf or csv file and attached to email

ARENA NX part numbers based on NIAGARA nodes
Model: Supervisor - 1 HAWK / EAGLHAWK with 200 proxy points. Does not support the Point List View


LSU25-18

Centraline Three-way rotary valve PN10
Accessories

Soldering socket witch gasket and cap nut, DN25, pipe size 18 mm



LSU25-22

Centraline Three-way rotary valve PN10
Accessories

Soldering socket witch gasket and cap nut, DN25, pipe size 22 mm



LSU25-28

Centraline Three-way rotary valve PN10
Accessories

Soldering socket witch gasket and cap nut, DN25, pipe size 28 mm



LSU32-22

Centraline Three-way rotary valve PN10
Accessories

Soldering socket witch gasket and cap nut, DN32, pipe size 22 mm



LSU32-28

Centraline Three-way rotary valve PN10
Accessories

Soldering socket witch gasket and cap nut, DN32, pipe size 28 mm



LSU32-35

Centraline Three-way rotary valve PN10
Accessories

Soldering socket witch gasket and cap nut, DN32, pipe size 35 mm



M100-AG

Centraline V5005T Kombi-FCU Pressure Independent Balancing and Control Valve
Accessories

M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.



M100-AO

Centraline V5005T Kombi-FCU Pressure Independent Balancing and Control Valve
Accessories

M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.



M100-BG

Centraline V5005T Kombi-FCU Pressure Independent Balancing and Control Valve
Accessories

M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.



M100-BO

Centraline V5005T Kombi-FCU Pressure Independent Balancing and Control Valve
Accessories

M100 actuators thermoelectric, 4.0 mm effective stroke, 90N, on/off.



M44-MOD-1M

Centraline V5005T Kombi-FCU Pressure Independent Balancing and Control Valve
Accessories

M44-MOD Cable for M4410 actuator, 1m, 10pcs



M44-MOD-1M/U

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Cable with plug, 1 meter, 3 x 0,22 mm2 (1 piece)



M44-MOD-1MH

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Non-halogen cable with plug, 1 meter, 3 x 0,22 mm2 (10 pieces)



M44-MOD-1MH/U

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Non-halogen cable with plug, 1 meter, 3 x 0,22 mm2 (1 piece)



M44-MOD-3M

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Cable with plug, 3 meter, 3 x 0,22 mm2 (10 pieces)



M44-MOD-3MH

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Non-halogen cable with plug, 3 meter, 3 x 0,22 mm2 (10 pieces)



M44-MOD-5M

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Cable with plug, 5 meter, 3 x 0,22 mm2 (10 pieces)



M44-MOD-5MH

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Required Cable (old cable of MT010 actuators can also be used)

Non-halogen cable with plug, 5 meter, 3 x 0,22 mm2 (10 pieces)



M44-VA10

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Valve Adapters M30 x 1,5

Valve adapter with closing dimension 11,5mm (10 pieces)



M44-VA50

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410
Valve Adapters M30 x 1,5

Valve adapter with closing dimension 10,5mm (10 pieces)



M4410E1510

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410

Electrical actuator for (radiator) valves with connection size M30 x 1,5. The actuator is supplied with the M44-VA10 adapter (closing dimension 11,5 mm). This suits the following valves:
V58xxA4, V58xxC4, VSO
V300, V2000
V2464, V2474
A separate adapter can be ordered (M44-VA50). With this adapter the actuator fits to the valves with closing dimension 10,5 mm.
Protection class: IP54
Effective stroke for Honeywell valves 2,5 mm; maximum stroke 4 mm.
Stem force: 100N
Control input signal: 0..10V=
Stroke: 2.5mm
Power loss action: stem extends
Runtime: 75s
Cable length: optional: 1, 3 ,5m
Required materials: check accessories

2,5 mm; 100 N
Supply voltage: 24 Vac


M4410K1515

Centraline Actuator thermoelectric 0..10V for radiator/terminal units, 2,5 mm 100 N, M4410

Electrical actuator for (radiator) valves with connection size M30 x 1,5. The actuator is supplied with the M44-VA10 adapter (closing dimension 11,5 mm). This suits the following valves:
V58xxA4, V58xxC4, VSO
V300, V2000
V2464, V2474
A separate adapter can be ordered (M44-VA50). With this adapter the actuator fits to the valves with closing dimension 10,5 mm.
Protection class: IP54
Effective stroke for Honeywell valves 2,5 mm; maximum stroke 4 mm.
Stem force: 100N
Control input signal: 0..10V=
Stroke: 2.5mm
Power loss action: stem extends
Runtime: 75s
Cable length: optional: 1, 3 ,5m
Required materials: check accessories

2,5 mm; 100 N
Supply voltage: 24 Vdc


M5410C1001

Centraline Fast motoric actuator for terminal unit/radiator, 6,5 mm 90 N, M5410

Electrical actuator on/off control, for valve series VS, V58.. DN15/20 and V100/V2000 TRV-series.
Protection class: IP54
Manual operation with valve cap.
Stem force: 90N
Control input signal: 2-pt
Stroke: 6.5mm
Power loss action: stem retracts
Runtime: 3,6/16s
Cable length: 1.5m

6,5 mm; 90 N
Supply voltage: 24 Vac/dc


M5410L1001

Centraline Fast motoric actuator for terminal unit/radiator, 6,5 mm 90 N, M5410

Electrical actuator on/off control, for valve series VS, V58.. DN15/20 and V100/V2000 TRV-series.
Protection class: IP54
Manual operation with valve cap.
Stem force: 90N
Control input signal: 2-pt
Stroke: 6.5mm
Power loss action: stem retracts
Runtime: 3,6/16s
Cable length: 1.5m

6,5 mm; 90 N
Supply voltage: 230 Vac


M6061A1013

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 10Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 1.5min
Position feedback: no
End switches: optional


M6061A1021

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 20Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 1.6min
Position feedback: no
End switches: optional


M6061A1039

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 30Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 2.3min
Position feedback: no
End switches: optional


M6061A1047

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 40Nm
Supply voltage: 24 Vac
Control input signal: 3-pt
Runtime: 3.5min
Position feedback: no
End switches: optional


M6061L1019

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 10Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 1.5min
Position feedback: no
End switches: optional


M6061L1027

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 20Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 1.6min
Position feedback: no
End switches: optional


M6061L1035

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 30Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 2.3min
Position feedback: optional
End switches: optional


M6061L1043

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Floating control
Torque: 40Nm
Supply voltage: 230 Vac
Control input signal: 3-pt
Runtime: 3.5min
Position feedback: no
End switches: optional


M6063A1003

Centraline Compact Line Rotary Actuator

Electrical actuator for valve series V5433A/G, V5442A/G.
Protection class: IP44
End switch function/capacity: SPST; capacity 1A inductive, 3 A resistive
Manual operation by declutch of gear.
Torque: 7Nm
Control input signal: 3-pt
Angle of rotation: 90o
Manual operation: yes
Runtime: 100s
Cable length: 1.5m


Supply voltage: 24 Vac
End switches: no


M6063A4007

Centraline Compact Line Rotary Actuator

Electrical actuator for valve series V5433A/G, V5442A/G.
Protection class: IP44
End switch function/capacity: SPST; capacity 1A inductive, 3 A resistive
Manual operation by declutch of gear.
Torque: 7Nm
Control input signal: 3-pt
Angle of rotation: 90o
Manual operation: yes
Runtime: 100s
Cable length: 1.5m


Supply voltage: 24 Vac
End switches: 2


M6063L1009

Centraline Compact Line Rotary Actuator

Electrical actuator for valve series V5433A/G, V5442A/G.
Protection class: IP44
End switch function/capacity: SPST; capacity 1A inductive, 3 A resistive
Manual operation by declutch of gear.
Torque: 7Nm
Control input signal: 3-pt
Angle of rotation: 90o
Manual operation: yes
Runtime: 100s
Cable length: 1.5m


Supply voltage: 230 Vac
End switches: no


M6063L4003

Centraline Compact Line Rotary Actuator

Electrical actuator for valve series V5433A/G, V5442A/G.
Protection class: IP44
End switch function/capacity: SPST; capacity 1A inductive, 3 A resistive
Manual operation by declutch of gear.
Torque: 7Nm
Control input signal: 3-pt
Angle of rotation: 90o
Manual operation: yes
Runtime: 100s
Cable length: 1.5m


Supply voltage: 230 Vac
End switches: 2


M6410C2023

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m


M6410C2031

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m


M6410C4029

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m


M6410C4037

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m


M6410L2023

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 230 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m


M6410L2031

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 230 Vac
Manual operation: yes
End switches: no
Cable length: 1.5m


M6410L4029

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 230 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m


M6410L4037

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 230 Vac
Manual operation: yes
End switches: 2
Cable length: 1.5m


M6422L1003

Centraline Actuator for V5421B1090

Protection class: IP54
Supply voltage: 230 Vac
Control input signal: 3-pt
Built in rotation limiter: no
Manual operation: yes
End switches: optional
Runtime: 150s
Torque: 40Nm


M7061E1012

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Modulating control
Torque: 10Nm
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Runtime: 1.5min
Position feedback: optional
End switches: no


M7061E1020

Centraline Standard Line Rotary Actuator

Electrical actuator for valve series VBG (DN40..DN50)
Protection class: IP54
Position indication: reversable scale plate
Manual operation by declutch of gear.
Angle of rotation: 90o
Manual operation: yes

Modulating control
Torque: 20Nm
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Runtime: 3.0min
Position feedback: optional
End switches: no


M7410A1001

Centraline Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A

Electrical actuator floating control, for valve series: V135, V136, V58..A4, V58..C4, VSO.
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Supply voltage: 24 Vac
Stem force: 90N
Control input signal: 3-pt
Stroke: 2.5mm
Runtime: 57s

2,5 mm; 90 N
Cable length: 0.9m


M7410A1001-10M

Centraline Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A

Electrical actuator floating control, for valve series: V135, V136, V58..A4, V58..C4, VSO.
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Supply voltage: 24 Vac
Stem force: 90N
Control input signal: 3-pt
Stroke: 2.5mm
Runtime: 57s

2,5 mm; 90 N
Cable length: 10m


M7410A1001-3M

Centraline Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A

Electrical actuator floating control, for valve series: V135, V136, V58..A4, V58..C4, VSO.
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Supply voltage: 24 Vac
Stem force: 90N
Control input signal: 3-pt
Stroke: 2.5mm
Runtime: 57s

2,5 mm; 90 N
Cable length: 3m


M7410A1001-5M

Centraline Actuator 3-pt for terminal unit/radiator, 2,5 mm 90 N, M7410A

Electrical actuator floating control, for valve series: V135, V136, V58..A4, V58..C4, VSO.
Protection class: IP43
Position indication: with red indicator
Manual operation with valve cap.
Supply voltage: 24 Vac
Stem force: 90N
Control input signal: 3-pt
Stroke: 2.5mm
Runtime: 57s

2,5 mm; 90 N
Cable length: 5m


M7410C1007

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 1.5m


M7410C1007-10M

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 10m


M7410C1007-3M

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 3m


M7410C1007-5M

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 5m


M7410C1015

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 1.5m


M7410C1015-5M

Centraline Actuator 3-pt for zone control, 6,5 mm 180/300 N, M6410/M7410

Electrical actuator floating control.
Protection class: IP43/IP42
Position indication: with red indicator
End switch function/capacity: SPDT; capacity 1 A inductive, 5 A resistive
For M7410-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Control input signal: 3-pt
Stroke: 6.5mm
Runtime: 150s

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Supply voltage: 24 Vac
Manual operation: no
End switches: no
Cable length: 5m


M7410E1002

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: no
End switches: no
Runtime: 150s
Cable length: 1.5m


M7410E1002-10M

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: no
End switches: no
Runtime: 150s
Cable length: 10m


M7410E1028

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Manual operation: no
End switches: no
Runtime: 150s
Cable length: 1.5m


M7410E2026

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: yes
End switches: no
Runtime: 150s
Cable length: 1.5m


M7410E2034

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Manual operation: yes
End switches: no
Runtime: 150s
Cable length: 1.5m


M7410E4022

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Manual operation: yes
End switches: 2
Runtime: 150s
Cable length: 1.5m


M7410E4030

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Manual operation: yes
End switches: 2
Runtime: 150s
Cable length: 1.5m


M7410E5001

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

2,7 mm; 90 N; for valve series V5004TY. 2,5 mm; 90 N; for valve series V5822A, V5823A/C, V5832A, V5833A/C, VSO and TRV V20/V30
Stem force: 90N
Stroke: 2.5mm
Manual operation: no
End switches: no
Runtime: 70s
Cable length: 1.5m


M7410E5001-10M

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

2,7 mm; 90 N; for valve series V5004TY. 2,5 mm; 90 N; for valve series V5822A, V5823A/C, V5832A, V5833A/C, VSO and TRV V20/V30
Stem force: 90N
Stroke: 2.5mm
Manual operation: no
End switches: no
Runtime: 70s
Cable length: 10m


M7410E5001-3M

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

2,7 mm; 90 N; for valve series V5004TY. 2,5 mm; 90 N; for valve series V5822A, V5823A/C, V5832A, V5833A/C, VSO and TRV V20/V30
Stem force: 90N
Stroke: 2.5mm
Manual operation: no
End switches: no
Runtime: 70s
Cable length: 3m


M7410E5001-5M

Centraline Actuator 0/2..10V for zone control, 90/180/300 N, M7410E

Electrical actuator modulating control.
Protection class: IP42
Position indication: with red indicator
End switch function/capacity: SPDT, capacity 1A inductive, 5A resistive
The control action is reversable. For M7410E1..-models, the valve cap can be used for manual adjustment. For models with 2 end switches, the 2nd switch is adjustable.
Supply voltage: 24 Vac
Control input signal: 0/2..10V=

2,7 mm; 90 N; for valve series V5004TY. 2,5 mm; 90 N; for valve series V5822A, V5823A/C, V5832A, V5833A/C, VSO and TRV V20/V30
Stem force: 90N
Stroke: 2.5mm
Manual operation: no
End switches: no
Runtime: 70s
Cable length: 5m


M7410G1008

Centraline LON actuator for radiator/zone control, 2,5/6,5 mm 90/180/300 N, M7410G

Electrical actuator with LON input signal.
Protection class: IP42
Position indication: with red indicator
LonMark(R) profile: input SNVT percent 0-100%
Transceiver type: FTT 10A
Contact input available for override function fully open or closed. Manual operation with valve cap. Configurable parameters for direct/reverse acting. LED-indication for servicing.
Supply voltage: 24 Vac
Control input signal: LON
Cable length: 1.5m

2,5 mm; 90 N; for valve series: V100 (thermostatic valves), V58..A4, V58..C4, VSO
Stem force: 90N
Stroke: 2.5mm
Runtime: 53s


M7410G1016

Centraline LON actuator for radiator/zone control, 2,5/6,5 mm 90/180/300 N, M7410G

Electrical actuator with LON input signal.
Protection class: IP42
Position indication: with red indicator
LonMark(R) profile: input SNVT percent 0-100%
Transceiver type: FTT 10A
Contact input available for override function fully open or closed. Manual operation with valve cap. Configurable parameters for direct/reverse acting. LED-indication for servicing.
Supply voltage: 24 Vac
Control input signal: LON
Cable length: 1.5m

6,5 mm; 180 N; for valve series: V5078B, V5822A, V5823A/C, V5832A, V5833A/C, VSM
Stem force: 180N
Stroke: 6.5mm
Runtime: 150s


M7410G1024

Centraline LON actuator for radiator/zone control, 2,5/6,5 mm 90/180/300 N, M7410G

Electrical actuator with LON input signal.
Protection class: IP42
Position indication: with red indicator
LonMark(R) profile: input SNVT percent 0-100%
Transceiver type: FTT 10A
Contact input available for override function fully open or closed. Manual operation with valve cap. Configurable parameters for direct/reverse acting. LED-indication for servicing.
Supply voltage: 24 Vac
Control input signal: LON
Cable length: 1.5m

6,5 mm; 300 N; for valve series: V5825B, V5832B2, V5833A2
Stem force: 300N
Stroke: 6.5mm
Runtime: 150s


MCD3

Centraline Relay module for on/off and 3-pt control

Two channel signal converter module.
For a signal change from 0..10Vdc (from external controller) into on/off and 3-pt control relay contact output.
Input signal: 2 x 0..10 Vdc
Output signal: relay K1 and K2 SPST contact 240V 0,2 A supplying 3-pt control of first analogue input
relay K3 SPDT contact 240V 2 A, supplying on/off control of second analogue input
Mounting: DIN rail
Power supply: 24Vacdc


MCE1

Centraline Voltage level switch

For conversion of an analogue output signal from a controller into an on/off output signal.
Input signal: 0..10 Vdc
Output signal: relay contact SPDT 250 V, 4 A; relay on with input voltage > 3 V, relay off with input voltage < 2,5 V
Manual operation functions: override switch with auto-off-on position
LED functions: yellow LED showing relay status
Mounting: DIN rail
Power supply: 24Vacdc


MCE2

Centraline Conversion module 24Vdc/relay

For conversion of an 24 Vdc signal from a digital output of a controller into an on/off output signal.
Input signal: 0 or 24 Vdc
Output signal: relay contact SPDT 250 V, 6 A; relay on with 24 V, off with 0 V input signal
Manual operation functions: override switch with auto-off-on position
LED functions: yellow LED showing relay status
Mounting: DIN rail
Power supply: 24Vacdc


MCE3

Centraline Conversion module 0..10Vdc - relay, 3 channel

Three channel signal converter module.
For a signal change from 0..10Vdc (from external controller) into an on/off relay contact output.
Input signal: 3x 0..10 Vdc
Output signal: relay K1/K2 SPDT contact 240 V, 2 A
relay K3 SPST contact 240 V, 2 A
Mounting: DIN rail
Power supply: 24Vacdc


MCM1

Centraline Status display module, 4 channel

Status indication module for external contacts.
Input signal: 4 x external potential free contacts
Output signal: 4 x 24Vacdc (from power supply)
Manual operation functions: 4 x switch for LED status inversion
LED functions: 4 x red or green LED showing the status of the input
Mounting: DIN rail
Power supply: 24Vacdc


MCP1

Centraline Manual positioning module

Manual positioning module for analogue output signals to manually adjust damper and valve actuators or to provide a fixed position.
Input signal: 0..10 Vdc
Output signal: 0..10 Vdc from input or from potentiometer (max. 1 mA)
Manual operation functions: potentiometer to adjust output signal 0..10Vdc; switch with auto/manual position
LED functions: red LED, intensity shows output level
Mounting: DIN rail
Potential free contact for feedback of manual override.
Power supply: 24Vacdc


ML6420A3007

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N
Supply voltage: 24 Vac
Power loss action: no
Manual operation: yes
Runtime: 1.0min
Spring return: no


ML6420A3015

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N
Supply voltage: 230 Vac
Power loss action: no
Manual operation: yes
Runtime: 1.0min
Spring return: no


ML6420A3023

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N
Supply voltage: 24 Vac
Power loss action: no
Manual operation: yes
Runtime: 0.5min
Spring return: no


ML6420A3031

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N
Supply voltage: 230 Vac
Power loss action: no
Manual operation: yes
Runtime: 0.5min
Spring return: no


ML6420A3072

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N
Supply voltage: 24 Vac
Power loss action: no
Manual operation: no
Runtime: 1.0min
Spring return: no


ML6421A3005

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421

Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes

20 mm; 1800 N
Supply voltage: 24 Vac
Stroke: 20mm
Runtime: 1.9min
Position feedback: optional


ML6421A3013

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421

Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes

20 mm; 1800 N
Supply voltage: 230 Vac
Stroke: 20mm
Runtime: 1.9min
Position feedback: no


ML6421B3004

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421

Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes

38 mm; 1800 N
Supply voltage: 24 Vac
Stroke: 38mm
Runtime: 3.5min
Position feedback: optional


ML6421B3012

Centraline Actuator 3-pt, 20/38 mm 1800 N, ML6421

Electrical actuator floating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate on the yoke
End switches: optional
Stem force: 1800N
Control input signal: 3-pt
Manual operation: yes

38 mm; 1800 N
Supply voltage: 230 Vac
Stroke: 38mm
Runtime: 3.5min
Position feedback: no


ML6425A3006

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N, Spring return
Supply voltage: 24 Vac
Power loss action: stem extends
Manual operation: no
Runtime: 1.8min
Spring return: yes


ML6425A3014

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N, Spring return
Supply voltage: 230 Vac
Power loss action: stem extends
Manual operation: no
Runtime: 1.8min
Spring return: yes


ML6425B3005

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N, Spring return
Supply voltage: 24 Vac
Power loss action: stem retracts
Manual operation: no
Runtime: 1.8min
Spring return: yes


ML6425B3021

Centraline Actuator 3-pt, 20 mm 600 N, ML6420/ML6425

Electrical actuator floating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Position feedback: optional
End switches: optional
For ML6425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Stem force: 600N
Control input signal: 3-pt
Stroke: 20mm

20 mm; 600 N, Spring return
Supply voltage: 230 Vac
Power loss action: stem retracts
Manual operation: no
Runtime: 1.8min
Spring return: yes


ML6435B1008

Centraline Actuator 3-pt for district heating, DHWS, spring return, 6,5 mm 400 N, ML6435

Electrical actuator floating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40)
Protection class: IP54
Approved according DIN EN 14597 in combination with V5825B.
Stem force: 400N
Control input signal: 3-pt
Stroke: 6.5mm
Power loss action: stem retracts
Runtime: 60s
Spring return: yes

6,5 mm; 400 N
Supply voltage: 24 Vac


ML6435B1016

Centraline Actuator 3-pt for district heating, DHWS, spring return, 6,5 mm 400 N, ML6435

Electrical actuator floating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40)
Protection class: IP54
Approved according DIN EN 14597 in combination with V5825B.
Stem force: 400N
Control input signal: 3-pt
Stroke: 6.5mm
Power loss action: stem retracts
Runtime: 60s
Spring return: yes

6,5 mm; 400 N
Supply voltage: 230 Vac


ML7420A6009

Centraline Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425

Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Supply voltage: 24 Vac
Stem force: 600N
Stroke: 20mm

20 mm; 600 N
Control input signal: 0/2..10V=
Power loss action: no
Manual operation: yes
Runtime: 1.0min
Spring return: no
Position feedback: 2..10V=


ML7420A6017

Centraline Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425

Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Supply voltage: 24 Vac
Stem force: 600N
Stroke: 20mm

20 mm; 600 N
Control input signal: 0/2..10V=
Power loss action: no
Manual operation: yes
Runtime: 0.5min
Spring return: no
Position feedback: 2..10V=


ML7420A6025

Centraline Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425

Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Supply voltage: 24 Vac
Stem force: 600N
Stroke: 20mm

20 mm; 600 N
Control input signal: 2..10V=
Power loss action: no
Manual operation: no
Runtime: 1.0min
Spring return: no
Position feedback: no


ML7421A3004

Centraline Actuator 0/2..10V, 20/38 mm 1800 N, ML7421

Electrical actuator modulating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: selectable: closed, half open, open
Position feedback: 2..10V=
End switches: optional
Supply voltage: 24 Vac
Stem force: 1800N
Control input signal: 0/2..10V=; 0/4..20mA
Manual operation: yes

20 mm; 1800 N
Stroke: 20mm
Runtime: 1.9min


ML7421B3003

Centraline Actuator 0/2..10V, 20/38 mm 1800 N, ML7421

Electrical actuator modulating control, for valve series: V5011, V5013, V5015, V5016, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: selectable: closed, half open, open
Position feedback: 2..10V=
End switches: optional
Supply voltage: 24 Vac
Stem force: 1800N
Control input signal: 0/2..10V=; 0/4..20mA
Manual operation: yes

38 mm; 1800 N
Stroke: 38mm
Runtime: 3.5min


ML7425A6008

Centraline Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425

Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Supply voltage: 24 Vac
Stem force: 600N
Stroke: 20mm

20 mm; 600 N, Spring return
Control input signal: 0/2..10V=
Power loss action: stem extends
Manual operation: no
Runtime: 1.8min
Spring return: yes
Position feedback: 2..10V=


ML7425B6007

Centraline Actuator 0/2..10V, 20 mm 600 N, ML7420/ML7425

Electrical actuator modulating control, for valve series: V5011, V5013, V5016A, V5025, V5049, V5050, V5328, V5329.
Protection class: IP54
Position indication: scale plate
Stem position at control signal loss: adjustable
End switches: optional
The control action is reversable. For ML7425-models: approved according DIN EN 14597 (up to 130 oC) in combination with V5016A/V5025A/V5328A/V5049A.
Supply voltage: 24 Vac
Stem force: 600N
Stroke: 20mm

20 mm; 600 N, Spring return
Control input signal: 0/2..10V=
Power loss action: stem retracts
Manual operation: no
Runtime: 1.8min
Spring return: yes
Position feedback: 2..10V=


ML7430E1005

Centraline Actuator 0/2..10V for district heating, DHWS, 6,5 mm 400 N, ML7430/ML7435

Electrical actuator modulating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40).
Protection class: IP54
For ML7435E1004: approved according DIN EN 14597 in combination with V5825B.
Supply voltage: 24 Vac
Stem force: 400N
Control input signal: 0/2..10V=
Stroke: 6.5mm

6,5 mm; 400 N
Power loss action: no
Manual operation: yes
Runtime: 15s
Spring return: no


ML7435E1004

Centraline Actuator 0/2..10V for district heating, DHWS, 6,5 mm 400 N, ML7430/ML7435

Electrical actuator modulating control, for valve series: V5825B. Also suitable for V5832B/V5833A-series (DN25..40).
Protection class: IP54
For ML7435E1004: approved according DIN EN 14597 in combination with V5825B.
Supply voltage: 24 Vac
Stem force: 400N
Control input signal: 0/2..10V=
Stroke: 6.5mm

6,5 mm; 400 N
Power loss action: stem retracts
Manual operation: no
Runtime: 60s
Spring return: yes


MP953A5005

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 34,5 or 69
Adjustable start point: 20.7...69kPa
Positioner: yes
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 70C
Diaphragm: 5inch


MP953A5039

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 34,5 or 69
Adjustable start point: 20.7...69kPa
Positioner: yes
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 70C
Diaphragm: 8inch


MP953A5054

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

38 mm
Pressure range kPa: 34,5 or 69
Adjustable start point: 20.7...69kPa
Positioner: yes
Stroke: 38mm
Action actuator stem: extends
Max. ambient temperature: 70C
Diaphragm: 13inch


MP953B5003

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 34,5 or 69
Adjustable start point: 20.7...69kPa
Positioner: yes
Stroke: 20mm
Action actuator stem: retracts
Max. ambient temperature: 70C
Diaphragm: 7inch


MP953C5001

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 13,8...48,3
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 5inch


MP953C5019

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 55,2...82,8
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 5inch


MP953C5027

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 27,6...75,9
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 5inch


MP953C5068

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 13,8...48,3
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 8inch


MP953C5076

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 55,2...82,8
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 8inch


MP953C5084

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 27,6...75,9
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 8inch


MP953C5142

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

38 mm
Pressure range kPa: 13,8...48,3
Adjustable start point: no
Positioner: no
Stroke: 38mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 13inch


MP953C5159

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

38 mm
Pressure range kPa: 27,6...75,9
Adjustable start point: no
Positioner: no
Stroke: 38mm
Action actuator stem: extends
Max. ambient temperature: 120C
Diaphragm: 13inch


MP953D5009

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 55,2...82,8
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: retracts
Max. ambient temperature: 120C
Diaphragm: 7inch


MP953D5025

Centraline Pneumatic actuator, MP953

Pneumatic actuator for valves in heating and air conditioning systems.
Actuators are suitable for valve series: V5011, V5013, V5015, V5049, V5050, V5016, V5025, V5328, V5329.
Protection class: IP54
Action: direct or reverse acting
Max. operating pressure: 140kPa
Rolling diaphragm
Max. safe air pressure: 172kPa

20 mm
Pressure range kPa: 27,6...75,9
Adjustable start point: no
Positioner: no
Stroke: 20mm
Action actuator stem: retracts
Max. ambient temperature: 120C
Diaphragm: 7inch


MT-ADAPT-HP

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Adapters

Mounting adapter for Herz/Polytherm valves; 10 units



MT-ADAPT-HW

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Adapters

Extra mounting adapters M30 x 1,5; 10 units



MT-CABLE-10M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Plug-in cable (not for models with end switch)

Cable 10 meter; 10 units



MT-CABLE-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Plug-in cable (not for models with end switch)

Cable 2,5 meter; 10 units



MT-CABLE-5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Plug-in cable (not for models with end switch)

Cable 5 meter; 10 units



MT-CLIP

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T
Accessories

Extra mounting clips; 10 units



MT4-024-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.2A
Cable length: 1m


MT4-024-NC-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.2A
Cable length: 2.5m


MT4-024-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.2A
Cable length: 1m


MT4-024-NO-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.2A
Cable length: 2.5m


MT4-024S-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 2.5mm
End switches: 1
Runtime: 4min
Initial current: 0.2A
Cable length: 1m


MT4-024S-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 2.5mm
End switches: 1
Runtime: 4min
Initial current: 0.2A
Cable length: 1m


MT4-230-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.4A
Cable length: 1m


MT4-230-NC-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.4A
Cable length: 2.5m


MT4-230-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.4A
Cable length: 1m


MT4-230-NO-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 2.5mm
End switches: no
Runtime: 4min
Initial current: 0.4A
Cable length: 2.5m


MT4-230S-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 2.5mm
End switches: 1
Runtime: 4min
Initial current: 0.4A
Cable length: 1m


MT4-230S-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

2,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 2.5mm
End switches: 1
Runtime: 4min
Initial current: 0.4A
Cable length: 1m


MT8-024-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 6.5mm
End switches: no
Runtime: 6min
Initial current: 0.2A
Cable length: 1m


MT8-024-NC-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 6.5mm
End switches: no
Runtime: 6min
Initial current: 0.2A
Cable length: 2.5m


MT8-024-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 6.5mm
End switches: no
Runtime: 6min
Initial current: 0.2A
Cable length: 1m


MT8-024-NO-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 6.5mm
End switches: no
Runtime: 6min
Initial current: 0.2A
Cable length: 2.5m


MT8-024S-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem extends
Stroke: 6.5mm
End switches: 1
Runtime: 6min
Initial current: 0.2A
Cable length: 1m


MT8-024S-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 24 Vac/dc
Power loss action: stem retracts
Stroke: 6.5mm
End switches: 1
Runtime: 6min
Initial current: 0.2A
Cable length: 1m


MT8-230-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 6.5mm
End switches: no
Runtime: 6.5min
Initial current: 0.4A
Cable length: 1m


MT8-230-NC-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 6.5mm
End switches: no
Runtime: 6.5min
Initial current: 0.4A
Cable length: 2.5m


MT8-230-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 6.5mm
End switches: no
Runtime: 6.5min
Initial current: 0.4A
Cable length: 1m


MT8-230-NO-2.5M

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 6.5mm
End switches: no
Runtime: 6.5min
Initial current: 0.4A
Cable length: 2.5m


MT8-230S-NC

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem extends
Stroke: 6.5mm
End switches: 1
Runtime: 6.5min
Initial current: 0.4A
Cable length: 1m


MT8-230S-NO

Centraline Actuator thermoelectric for zone control 2,5/6,5 mm 90 N, Smart-T

Electrical actuator on/off control, and PWM control.
Protection class: IP44
Position indication: with red indicator
End switch function/capacity: SPST, capacity 5(3) A; contact closes at power on
Stem force: 90N
Control input signal: 2-pt
Actuator supplied with mounting clip (MT-CLIP) and M30 x 1,5 adapter (MT-ADAPT-HW).
Other adapters on request.
Other cable length, or special connectors, on request.
Effective stroke for valves 2,5/6,5 mm; maximum stroke 4/8 mm.
Fits to closing dimension 11,5 +/- 0,3 mm

6,5 mm; 90 N
Supply voltage: 230 Vac
Power loss action: stem retracts
Stroke: 6.5mm
End switches: 1
Runtime: 6.5min
Initial current: 0.4A
Cable length: 1m


MVC-40-AC3

Centraline EAGLEHAWK Integrated Plant Control
Extra parts for EAGLEHAWK controller

Strain relief; package of 10



MVC-80-AC1

Centraline EAGLEHAWK Integrated Plant Control
Extra parts for EAGLEHAWK controller

Terminal cover (color: RAL9011); package of 10



MVC-80-AC2

Centraline EAGLEHAWK Integrated Plant Control
Extra parts for EAGLEHAWK controller

Front door mounting accessory (color: RAL9011); package of 10



MVN613A1500

Centraline Rotary Actuator, MVN

Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m

Floating control
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Runtime: 108s


MVN643A1500

Centraline Rotary Actuator, MVN

Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m

Floating control
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
Runtime: 30s


MVN663A1500

Centraline Rotary Actuator, MVN

Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m

Floating control
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Runtime: 108s


MVN713A1500

Centraline Rotary Actuator, MVN

Electrical actuator for VBG control ball valves, DN15-DN32.
Actuator can easily be clicked on valve - no tool required.
Protection class: IP40
Position indication: scale plate
Torque: 3Nm
Angle of rotation: 90o
Manual operation: yes
Cable length: 1.5m

Modulating control. Control action reversable.
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Runtime: 90s


MVNAAA/U

Centraline Two way characterized control ball valves, PN25, DN15-50, VBG2
Accessories for DN15..32 valves

Replacement valve adaptor standard profile, for VBG valves, DN15..DN32



MVNAT3/B

Centraline Rotary Actuator, MVN
Accessories

Replacement screw terminal block, pluggable



N05010

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: no
Position feedback: 0/2..10V=
Runtime: 90/110s
Torque: 5Nm
Damper area: 1m2


N05010-SW2

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Position feedback: 0/2..10V=
Runtime: 90/110s
Torque: 5Nm
Damper area: 1m2


N05230-2POS

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 1 square meter
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: max. 110s
Torque: 5Nm
Damper area: 1m2


N0524

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: no
Position feedback: no
Runtime: 110s
Torque: 5Nm
Damper area: 1m2


N0524-SW2

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 1 square meter
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: 2
Position feedback: no
Runtime: 110s
Torque: 5Nm
Damper area: 1m2


N10010

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: no
Position feedback: 0/2..10V=
Runtime: 90/110s
Torque: 10Nm
Damper area: 2m2


N10010-SW2

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;2/3-pt
End switches: 2
Position feedback: 0/2..10V=
Runtime: 90/110s
Torque: 10Nm
Damper area: 2m2


N10230-2POS

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 2 square meters
Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: max. 140s
Torque: 10Nm
Damper area: 2m2


N1024

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: no
Position feedback: no
Runtime: 110s
Torque: 10Nm
Damper area: 2m2


N1024-SW2

Centraline Damper actuator 5/10 Nm, SmartAct

Direct coupled actuators for air dampers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
End switch function/capacity: SPDT switch 230 V, 5(3) A for models with end switch
Shaft mounting: for round shafts 8..16 mm; square shafts 6..13 mm
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Rotation direction selectable by switch.
Adjustable mechanical end limits included.
Built in rotation limiter: yes
Manual operation: yes

For damper area of 2 square meters
Supply voltage: 24 Vac/dc
Control input signal: 2/3-pt
End switches: 2
Position feedback: no
Runtime: 110s
Torque: 10Nm
Damper area: 2m2


N20010

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 4 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Built in rotation limiter: yes
End switches: optional
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 20Nm
Damper area: 4m2


N20010-SW2

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 4 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Built in rotation limiter: yes
End switches: 2
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 20Nm
Damper area: 4m2


N20230

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 4 square meters
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2


N20230-SW2

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 4 square meters
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: 2
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2


N2024

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 4 square meters
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2


N2024-SW2

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 4 square meters
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Built in rotation limiter: yes
End switches: 2
Position feedback: no
Runtime: 110s
Torque: 20Nm
Damper area: 4m2


N34010

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 6 square meters
Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=
Built in rotation limiter: no
End switches: optional
Position feedback: 0/2..10V=
Runtime: 95s
Torque: 34Nm
Damper area: 6m2


N34230

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 6 square meters
Supply voltage: 230 Vac
Control input signal: 2/3-pt
Built in rotation limiter: no
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 34Nm
Damper area: 6m2


N3424

Centraline Damper actuator 20/34 Nm, SmartAct

Direct-coupled actuator with self-centering shaft adapter.
For air dampers, air handlers, ventilation flaps, louvers and VAV-units.
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: SPDT switch 230V, 5 (3) A for models with end switch
Shaft mounting: for round shafts 10..27 mm; square shafts 10..18 mm
Rotation direction selectable by switch.
When power is removed, the actuator remains in position.
Removable wiring box, with cable gland M20x1,5 1/2" NPT.
Actuator supplied with complete package mounting parts.
For modulating control models: Control input signal can be voltage or current.
For modulating control models: Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Manual operation: yes

For damper area of 6 square meters
Supply voltage: 24 Vac
Control input signal: 2/3-pt
Built in rotation limiter: no
End switches: optional
Position feedback: no
Runtime: 110s
Torque: 34Nm
Damper area: 6m2


NX-FAN-4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: NXL HVAC / NXS spare part fan size 4 (HVAC03-HVAC12, NXS0003-NXS0012)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NX-FAN-5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: NXL HVAC / NXS spare part fan size 5 (HVAC16-HVAC31, NXS0016-NXS0031)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NX-FAN-6

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: NXL HVAC / NXS spare part fan size 6 (HVAC38-HVAC61, NXS0038-NXS0061)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NX-FAN-7

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Main cooling fan spare parts for inverters
Product description: NXS spare part fan size 7 (NXS0072-NXS0105)
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NX-FAN-8

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, main fan, frame size 8, power 75 - 110 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-8-SET1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan kit, main fan and internal fan, frame size 8, 62 - 140 A
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-8-SET2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan kit, main fan and two internal fans, frame size 8, 168 - 205 A
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-9-FULLSET

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan kit, (main fans, 2x intern fans, fan power supply), frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-9-SET

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan set, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-INT-FR9-1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, internal fan, 52 mm, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-INT-FR9-2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, internal fan, 80 mm, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-INT4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NX drives, internal fan, frame size 4, power 1.15 - 5 kW
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NX-FAN-INT5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NX drives, internal fan, frame size 5, power 7.5 - 15 kW
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NX-FAN-INT6-7

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NX drives, internal fan, frame size 6-7, power 18.5 - 55 kW
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NX-FAN-INT8

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, internal fan, frame size 8, 75 - 110 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-SUP-FR08

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan power supply kit, frame size 8, power 75 - 110 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NX-FAN-SUP-FR09

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan power supply kit, frame size 9, power 132 - 160 kW
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NXIP54FR4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL HVAC/NXS IP21 to IP54 upgrade kits
Product description: IP54 enclosure upgrade kit for NXL HVAC/NXS size 4 (HVAC03-HVAC12, NXS0003-NXS0012)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXIP54FR5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL HVAC/NXS IP21 to IP54 upgrade kits
Product description: IP54 enclosure upgrade kit for NXL HVAC/NXS size 5 (HVAC16-HVAC31, NXS0016-NXS0031)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXIP54FR6

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL HVAC/NXS IP21 to IP54 upgrade kits
Product description: IP54 enclosure upgrade kit for NXL HVAC/NXS size 6 (HVAC38-HVAC61, NXS0038-NXS0061)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXLOPTAA

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 3 digital inputs, 1 relay (NO/NC), 1 digital output
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NXLPANC

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL Display panels
Product description: NXL standard 7-segment display
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NXLPANRS

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS PC connection tools and cables
Product description: NXL RS232 adapter (for PC connection)
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


NXOPTA1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: standard NXS slot A board: 6 DI, 1 DO (open collector), 2 AI, 1 AO
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NXOPTB2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 2 relays (1 NO, 1 NO/NC), 1 thermistor
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXOPTB8

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 3 Pt100 input
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NXOPTC2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: Modbus/N2 (RS485)
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NXOPTC3

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: Profibus DP
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXOPTC6

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: CANopen (slave)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXOPTC7

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: DeviceNet
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXOPTCJ

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: BACnet MS/TP (RS485)
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


NXPANA

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXS Display panels
Product description: NXS standard alpha-numeric display
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NXPANG

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXS Display panels
Product description: NXS special display for Cyrillic or Chinese letters
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NXS-CONTROL-BOX

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Control Spares
Product description: Varnished control unit for NXS with enclosure
HVAC400: no
NXL HVAC: no
NXS: yes
HVAC232/402: no


NXS0003V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 1.1kW
Low overload Icont: 3.1A
High overload (for Machines): 0.75kW
High overload Icont: 2.2A
Brake chopper: integrated


NXS0003V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 1.1kW
Low overload Icont: 3.1A
High overload (for Machines): 0.75kW
High overload Icont: 2.2A
Brake chopper: integrated


NXS0004V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 1.5kW
Low overload Icont: 4A
High overload (for Machines): 1.1kW
High overload Icont: 3.1A
Brake chopper: integrated


NXS0004V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 1.5kW
Low overload Icont: 4A
High overload (for Machines): 1.1kW
High overload Icont: 3.1A
Brake chopper: integrated


NXS0005V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 2.2kW
Low overload Icont: 5.4A
High overload (for Machines): 1.5kW
High overload Icont: 4A
Brake chopper: integrated


NXS0005V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 2.2kW
Low overload Icont: 5.4A
High overload (for Machines): 1.5kW
High overload Icont: 4A
Brake chopper: integrated


NXS0007V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 3kW
Low overload Icont: 7A
High overload (for Machines): 2.2kW
High overload Icont: 5.4A
Brake chopper: integrated


NXS0007V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 3kW
Low overload Icont: 7A
High overload (for Machines): 2.2kW
High overload Icont: 5.4A
Brake chopper: integrated


NXS0009V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 4kW
Low overload Icont: 9A
High overload (for Machines): 3kW
High overload Icont: 7A
Brake chopper: integrated


NXS0009V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 4kW
Low overload Icont: 9A
High overload (for Machines): 3kW
High overload Icont: 7A
Brake chopper: integrated


NXS0012V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 5.5kW
Low overload Icont: 12A
High overload (for Machines): 4kW
High overload Icont: 9A
Brake chopper: integrated


NXS0012V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 5.5kW
Low overload Icont: 12A
High overload (for Machines): 4kW
High overload Icont: 9A
Brake chopper: integrated


NXS0016V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 7.5kW
Low overload Icont: 16A
High overload (for Machines): 5.5kW
High overload Icont: 12A
Brake chopper: integrated


NXS0016V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 7.5kW
Low overload Icont: 16A
High overload (for Machines): 5.5kW
High overload Icont: 12A
Brake chopper: integrated


NXS0022V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 11kW
Low overload Icont: 22A
High overload (for Machines): 7.5kW
High overload Icont: 16A
Brake chopper: integrated


NXS0022V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 11kW
Low overload Icont: 22A
High overload (for Machines): 7.5kW
High overload Icont: 16A
Brake chopper: integrated


NXS0031V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 15kW
Low overload Icont: 31A
High overload (for Machines): 11kW
High overload Icont: 22A
Brake chopper: integrated


NXS0031V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 15kW
Low overload Icont: 31A
High overload (for Machines): 11kW
High overload Icont: 22A
Brake chopper: integrated


NXS0038V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 18.5kW
Low overload Icont: 38A
High overload (for Machines): 15kW
High overload Icont: 31A
Brake chopper: integrated


NXS0038V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 18.5kW
Low overload Icont: 38A
High overload (for Machines): 15kW
High overload Icont: 31A
Brake chopper: integrated


NXS0045V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 22kW
Low overload Icont: 45A
High overload (for Machines): 18.5kW
High overload Icont: 38A
Brake chopper: integrated


NXS0045V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 22kW
Low overload Icont: 45A
High overload (for Machines): 18.5kW
High overload Icont: 38A
Brake chopper: integrated


NXS0061V35A2H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 30kW
Low overload Icont: 61A
High overload (for Machines): 22kW
High overload Icont: 45A
Brake chopper: integrated


NXS0061V35A5H1

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 30kW
Low overload Icont: 61A
High overload (for Machines): 22kW
High overload Icont: 45A
Brake chopper: integrated


NXS0072V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 37kW
Low overload Icont: 72A
High overload (for Machines): 30kW
High overload Icont: 61A
Brake chopper: optional


NXS0072V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 37kW
Low overload Icont: 72A
High overload (for Machines): 30kW
High overload Icont: 61A
Brake chopper: optional


NXS0087V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 45kW
Low overload Icont: 87A
High overload (for Machines): 37kW
High overload Icont: 72A
Brake chopper: optional


NXS0087V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 45kW
Low overload Icont: 87A
High overload (for Machines): 37kW
High overload Icont: 72A
Brake chopper: optional


NXS0105V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 55kW
Low overload Icont: 105A
High overload (for Machines): 45kW
High overload Icont: 87A
Brake chopper: optional


NXS0105V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 55kW
Low overload Icont: 105A
High overload (for Machines): 45kW
High overload Icont: 87A
Brake chopper: optional


NXS0140V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 75kW
Low overload Icont: 140A
High overload (for Machines): 55kW
High overload Icont: 105A
Brake chopper: optional


NXS0140V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 75kW
Low overload Icont: 140A
High overload (for Machines): 55kW
High overload Icont: 105A
Brake chopper: optional


NXS0168V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 90kW
Low overload Icont: 170A
High overload (for Machines): 75kW
High overload Icont: 140A
Brake chopper: optional


NXS0168V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 90kW
Low overload Icont: 170A
High overload (for Machines): 75kW
High overload Icont: 140A
Brake chopper: optional


NXS0205V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 110kW
Low overload Icont: 205A
High overload (for Machines): 90kW
High overload Icont: 170A
Brake chopper: optional


NXS0205V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 110kW
Low overload Icont: 205A
High overload (for Machines): 90kW
High overload Icont: 170A
Brake chopper: optional


NXS0260V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 132kW
Low overload Icont: 261A
High overload (for Machines): 110kW
High overload Icont: 205A
Brake chopper: optional


NXS0260V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 132kW
Low overload Icont: 261A
High overload (for Machines): 110kW
High overload Icont: 205A
Brake chopper: optional


NXS0310V35A2H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP21
Power: 160kW
Low overload Icont: 300A
High overload (for Machines): 132kW
High overload Icont: 245A
Brake chopper: optional


NXS0310V35A5H0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP54, wall mounted; Emissions EN61800-3 (category C2), C-Tick
Protection class: IP54
Power: 160kW
Low overload Icont: 300A
High overload (for Machines): 132kW
High overload Icont: 245A
Brake chopper: optional


NXS0385V35A2L0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, stand-alone cabinet; Emissions EN61800-3 (category 3)
Protection class: IP21
Power: 200kW
Low overload Icont: 385A
High overload (for Machines): 160kW
High overload Icont: 300A
Brake chopper: no


NXS0460V35A2L0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, stand-alone cabinet; Emissions EN61800-3 (category 3)
Protection class: IP21
Power: 250kW
Low overload Icont: 460A
High overload (for Machines): 200kW
High overload Icont: 385A
Brake chopper: no


NXS0590V35A2L0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, stand-alone cabinet; Emissions EN61800-3 (category 3)
Protection class: IP21
Power: 315kW
Low overload Icont: 590A
High overload (for Machines): 250kW
High overload Icont: 520A
Brake chopper: no


NXS0650V35A2L0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, stand-alone cabinet; Emissions EN61800-3 (category 3)
Protection class: IP21
Power: 355kW
Low overload Icont: 650A
High overload (for Machines): 315kW
High overload Icont: 590A
Brake chopper: no


NXS0730V35A2L0

Centraline Inverters 1,1..400kW, IP21/IP54, NXS

Speed controller for induction motors, with built-in RFI filters. EMC and LVD compliant.
The Honeywell inverters are suitable for High/Low Overload (constant/variable torque) applications. To control pumps and fans for heating , ventilation and air conditioning systems, normally Low Overload inverters are used. Industrial or process installations normally require High Overload inverters.
Features: high featured software package with predefined applications
start-up wizard
detachable multilingual HMI-panel with memory and backup functions
flexible I/O configuration; 5 slots
inputs/outputs: 2 analog inputs, 6 digital inputs, 2 relays, 1 digital output, 1 thermistor input, 1 analog output
Series: NXS
Voltage: 400V
Output frequency: 0...320Hz
Frequency resolution: 0.01Hz
Serial communication: optional: LonWorks, Modbus RTU, Profibus DP, BACnet, Ethernet (Mobus/TCP), N2, DeviceNet, CANopen
Immunity: fulfills all EMC immunity requirements
Safety: EN61800-5, CE, UL, cUL
RFI-filter: integrated
http://hwll.co/inverter
1 phase input: no
3 phases input: yes

IP21, stand-alone cabinet; Emissions EN61800-3 (category 3)
Protection class: IP21
Power: 400kW
Low overload Icont: 730A
High overload (for Machines): 355kW
High overload Icont: 650A
Brake chopper: no


OPT-BT-MC02-5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Control Spares
Product description: 5 pieces of real time clock batteries
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


OPTB1

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 6 digital inputs/outputs (programmable)
HVAC400: yes
NXL HVAC: no
NXS: yes
HVAC232/402: no


OPTB2

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 1 Thermistor, 2x RO
HVAC400: no
NXL HVAC: no
NXS: no
HVAC232/402: yes


OPTB4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 1 analog input (mA), 2 analog output (mA)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


OPTB5

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 3 relays (NO)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


OPTB9

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 1 relay, 5 Vac inputs (42..240 Vac)
HVAC400: yes
NXL HVAC: no
NXS: yes
HVAC232/402: no


OPTBF

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: 1 analog input (mA/V), 1 relay (NO), 1 digital output (open collector)
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


OPTBH

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Input/output expander cards
Product description: Pt1000, Ni1000, KTY84x
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: yes


OPTC4

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: LonWorks
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


OPTE9

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

Fieldbus cards
Product description: Modbus TCP, Ethernet/IP
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: yes


PMK-EEM400

Centraline Electrical Energy Meters, 3 phases, 65A, 2 Tariff, LCD, EEM400-D


Panel mounting kit for front door of cabinet



PW20

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 interface modules
Product description: M-Bus connection module, for 20 M-Bus meters


PW3

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 interface modules
Product description: M-Bus connection module, for 3 M-Bus meters


PW60

Centraline Connected Building Management, HAWK 8000

HAWK 8000 is a powerful hardware and software platform designed to manage HVAC and non-HVAC systems (e.g. lighting, security, life safety) in a building and across multiple buildings. It therefore supports all common communication protocols, such as BACnet, LON, Modbus, M-BUS, KNX IP, Fidelio, SNMP, C-Bus and many more. HAWK 8000 allows to make use of the CentraLine Application Library, which ensures unparalleled energy efficiency as well as maximum application reliability. This ensures that International Standards like the EN 15232 are met.
Hardware inputs/Outputs
CentraLine Panel-Bus I/O modules (CLIOP)
CentraLine LON I/O modules (CLIOL)
Onboard communication inputs/outputs: Dual Ethernet 10/100Mbps, 2 RS485 ports
Optional communication inputs/outputs via expansion modules: Up to 4 RS485 ports, up to 4 RS232 ports, up to 4 LON FTT10A ports
Drivers
Included communication Drivers: BACnet/IP, BACnet MSTP, DALI, FOX and FOXS, LON KNX/IP FTT10A and IP, M-Bus, Modbus all types, oBIX, Open ADR, SNMP, OPC-DA
Included CentraLine drivers and enhancements:, Panel-Bus , C-Bus, LON IO, BACnet Integration, Project documentation and print,out, IO Creation and EnOcean
Optional drivers and applications: SMS, Fidelio, ENERGY VISION
Web Server and Programming
Web Server: Supports most common mobile and PC browsers- Provides JAVA-free web-pages (HTML5)- Provides full-functional read and write access to the application, including programming
Programming: Full and web-browser based programming Option,Programming via COACH NX or COACH AX
Cyber Security
HAWK 8000 incorporates industry best practices for cyber security. This includes features such as secure boot, enforcement of strong hashed passwords, role-based access control, TLSv1 for secure communications, certificate management tools for authentication, audit log and Java-free access via web-browsers

HAWK 8000 interface modules
Product description: M-Bus connection module, for 50 M-Bus meters


RET-NX-FAN-8-SET

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan retrofit kit, (main fan, power supply), frame size 8, power 75 - 110 kW, SN -13068696, Date: 2012-10-05
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


RET-NX-FAN-9-SET

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NX Cooling Fans
Product description: NXS drives, fan retrofit kit, (main fan, power supply), frame size 9, power 132 - 160 kW, SN -13068696, Date: 2012-10-05
HVAC400: no
NXL HVAC: yes
NXS: no
HVAC232/402: no


RF20

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Sensors

Room temperature sensor NTC



RFI-0012-5-IP54

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 4
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


RFI-0031-5-IP54

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 5
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


RFI-0061-5-IP54

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 6
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


RFI-0105-5-IP54

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive HVAC C1 conducted emission filter IP54
Product description: C1 RFI-filter for size 7
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: no


RS232C-4M

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS PC connection tools and cables
Product description: 4 m RS232 cable
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


RS232C2M

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS PC connection tools and cables
Product description: 2 m RS232 cable
HVAC400: no
NXL HVAC: yes
NXS: yes
HVAC232/402: no


S03010

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: no
Position feedback: 0..10V=
Runtime: 90s
Torque: 3Nm
Damper area: 0.6m2


S03010-SW1

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 1
Position feedback: 0..10V=
Runtime: 90s
Torque: 3Nm
Damper area: 0.6m2


S03230-2POS

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2


S03230-2POS-SW1

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2


S0324-2POS

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2


S0324-2POS-SW1

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 3Nm
Damper area: 0.6m2


S05010

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: no
Position feedback: 0..10V=
Runtime: 90s
Torque: 5Nm
Damper area: 1m2


S05010-SW1

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 1
Position feedback: 0..10V=
Runtime: 90s
Torque: 5Nm
Damper area: 1m2


S05230-2POS

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2


S05230-2POS-SW1

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2


S0524-2POS

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: no
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2


S0524-2POS-SW1

Centraline Damper actuator 3/5 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 1 SPDT switch 250 V, 8 (5) A; adjustable setting between 0o and 95o
Shaft mounting: for round shafts 9..16 mm; square shafts 6..13 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Removable wiring box, without cable gland (M20x1,5).
Durable plastic housing with built-in mechanical end-limits.
Spring return: yes
Manual operation: no
Spring return timing: 25s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 1
Position feedback: no
Runtime: 45s
Torque: 5Nm
Damper area: 1m2


S10010

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: optional
Position feedback: 0..10V=
Runtime: 90s
Torque: 10Nm
Damper area: 1.5m2


S10010-SW2

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 2
Position feedback: 0..10V=
Runtime: 90s
Torque: 10Nm
Damper area: 1.5m2


S10230-2POS

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2


S10230-2POS-SW2

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2


S1024-2POS

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2


S1024-2POS-SW2

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 10Nm
Damper area: 1.5m2


S20010

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: optional
Position feedback: 0..10V=
Runtime: 90s
Torque: 20Nm
Damper area: 4.6m2


S20010-SW2

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 0/2..10V=;3-pt
End switches: 2
Position feedback: 0..10V=
Runtime: 90s
Torque: 20Nm
Damper area: 4.6m2


S20230-2POS

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2


S20230-2POS-SW2

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 230 Vac
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2


S2024-2POS

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: optional
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2


S2024-2POS-SW2

Centraline Damper actuator 10/20 Nm, SmartAct springreturn

Direct-coupled actuator with self-centering shaft adapter.
For the operation of quarter-turn air dampers in safety related applications requiring springreturn fail-safe operation (e.g. frost protection).
Protection class: IP54
Position indication: rotational angle scales 0..90o, 90..0o
End switch function/capacity: models with 2 SPDT switches 250 V, 3 (1,5) A; fixed setting at 7o and 85o
Shaft mounting: for round shafts 10..27 mm; square shafts 13..19 mm
Rotation direction selectable by flipping the actuator 180o around its vertical axis.
Actuator supplied with complete package mounting parts.
Autoadapt dipswitch. With this function the full span of the control input signal will be used for the applicable angle or rotation.
Removable wiring box, without cable gland (M16x1,5).
Actuator can be locked and manually wound.
Spring return: yes
Manual operation: yes
Spring return timing: 20s


Supply voltage: 24 Vac/dc
Control input signal: 2-pt
End switches: 2
Position feedback: no
Runtime: 45s
Torque: 20Nm
Damper area: 4.6m2


S6065A1003

Centraline Paddle flow switches for liquid (S6065)

The flow switches are designed for monitoring flow rates in pipes employed in HVAC applications.
For monitoring flow in water, oil, cooling circuits, and lubrication systems.
Protection class: IP65
Switch function/capacity: SPDT, capacity 250Vac, (8)15 A
Setpoint device: screw
Max. media temperature: 120C
Setpoint range: 0,6..165 m3/h pipe size dependent

Liquid
Media: liquid non-aggressive
Max. pressure: 11bar


S6065A2001

Centraline Paddle flow switches for liquid (S6065)

The flow switches are designed for monitoring flow rates in pipes employed in HVAC applications.
For monitoring flow in water, oil, cooling circuits, and lubrication systems.
Protection class: IP65
Switch function/capacity: SPDT, capacity 250Vac, (8)15 A
Setpoint device: screw
Max. media temperature: 120C
Setpoint range: 0,6..165 m3/h pipe size dependent

Liquid
Media: liquid aggressive
Max. pressure: 30bar


SCI-10

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Smile Connect

Installation kit for installers, for initial set up



SCN-10

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Smile Connect

Gateway for remote access with App



SCS-12

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Mounting accessories for panel models

Base for touch protection



SCW-10

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Smile Connect

WiFi stick for SCN-10



SDC12-31N

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Romanian, Russian, Polish, Hungarian, Czech, Turkish, English
Burner output: 1/2 stages
Heating circuit: 2x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 12 (3 var.)


SDC12-31PM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 2x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 12 (3 var.)


SDC12-31PMN

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Italian, Spanish, Swedish, Norwegian; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 2x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 12 (3 var.)


SDC12-31WM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Wall mounting, HxWxD = 96x285x90 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 2x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 12 (3 var.)


SDC3-10N

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Romanian, Russian, Polish, Hungarian, Czech, Turkish, English
Burner output: 1 stage
Heating circuit: pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-10PM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1 stage
Heating circuit: pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-10PMN

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Italian, Spanish, Swedish, Norwegian; 11 other display languages also supported
Burner output: 1 stage
Heating circuit: pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-10WM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Wall mounting, HxWxD = 96x285x90 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1 stage
Heating circuit: pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-40N

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Romanian, Russian, Polish, Hungarian, Czech, Turkish, English
Burner output: no
Heating circuit: 1x: mixing valve + pump
Domestic Hot Water: no
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-40PM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: no
Heating circuit: 1x: mixing valve + pump
Domestic Hot Water: no
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-40PMN

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Italian, Spanish, Swedish, Norwegian; 11 other display languages also supported
Burner output: no
Heating circuit: 1x: mixing valve + pump
Domestic Hot Water: no
Additional output: no
Hardware inputs: 4 (1 var.)


SDC3-40WM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Wall mounting, HxWxD = 96x285x90 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: no
Heating circuit: 1x: mixing valve + pump
Domestic Hot Water: no
Additional output: no
Hardware inputs: 4 (1 var.)


SDC7-21N

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Romanian, Russian, Polish, Hungarian, Czech, Turkish, English
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 6 (SDC 1v DHC 3v)


SDC7-21PM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 6 (SDC 1v DHC 3v)


SDC7-21PMN

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Italian, Spanish, Swedish, Norwegian; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 6 (SDC 1v DHC 3v)


SDC7-21WM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Wall mounting, HxWxD = 96x285x90 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: no
Hardware inputs: 6 (SDC 1v DHC 3v)


SDC9-21N

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: Romanian, Russian, Polish, Hungarian, Czech, Turkish, English
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 11 (3 var.)


SDC9-21PM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Panel mounting, HxWxD = 96x144x75 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 11 (3 var.)


SDC9-21WM

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE

Microprocessor controller with fixed hard- and software. Configuration with 15 sets of parameters. Remote access with App and Gateway.
For all Heating and District Heating applications with:
direct heating circuit and/or mixed heating circuit(s)
boiler burner
domestic hot water
heat exchanger valve
Control software: the software application can be selected, by keying in a planttype code, and can be adjusted with parameters; or use no code number and configure the application with the parametersets only
Modes of operation: heating without time program, eco, summer, manu, auto
Time program: heating with own week clock, DHW with own week clock, 15 vacation periods
Protection class: IP30
Max. ambient temperature: 50C
Power supply: 230Vac
Batteries: included 3VLi
Bus system description: Honeywell bus sytem for max. 5 SMILE controllers, and 3 setpoint units per controller; max. buslength 100 m; the controller can also be used as stand-alone controller.
OpenTherm for all models, except SDC3-40..
Hardware outputs: all outputs are relay outputs with a maximum contact load of 2A 250V
the standard relay outputs are for pumps and valves, and are controlled from the selected application; mixing valves need 2 output relays
the function for the additional relay outputs can be set with parameters
Applicable sensor types: NTC 20 kohm
One of the hardware inputs is for a pulse contact. This can be used for example for counting running hours. With parametersettings the amount of counted pulses can be used for switching pumps or boilers.
ErP Class: VI

Wall mounting, HxWxD = 96x285x90 mm; Display languages and documentation: German, French, English, Dutch; 11 other display languages also supported
Burner output: 1/2 stages
Heating circuit: 1x: mixing valve + pump; pump
Domestic Hot Water: loading pump
Additional output: 2 variable
Hardware inputs: 11 (3 var.)


SDW10EE

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Remote setpoint selector with temperature sensor, night, day and auto switch

Setpoint unit Eastern Europe



SDW10WE

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Remote setpoint selector with temperature sensor, night, day and auto switch

Setpoint unit Western Europe



SDW30

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Comfortable digital remote setpoint selector with display, temperature sensor, access to the controller functions

Digital setpoint unit Western Europe



SDW30N

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Comfortable digital remote setpoint selector with display, temperature sensor, access to the controller functions

Digital setpoint unit Eastern Europe



SF20-B54

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Sensors

Water temperature sensor, NTC, strap on pipe



SIN-0010-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 10 A (40oC), 8,8 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SIN-0018-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 18 A (40oC), 16 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SIN-0032-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 32 A (40oC), 28 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SIN-0048-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 48 A (40oC), 42 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SIN-0075-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 75 A (40oC), 66 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SIN-0110-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 110 A (40oC), 97 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SIN-0180-5-0-P

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

NXL/NXS Sine-wave output filters 380-500V, IP00 Selection to be done so that the nominal current of the inverter cannot exceed the nominal current of the filter
Product description: Filter for Nominal current of 180 A (40oC), 155 A (50oC)
HVAC400: yes
NXL HVAC: yes
NXS: yes
HVAC232/402: no


SMARTDRIVE-USBC

Centraline Parts and accessories for inverters

Honeywell inverter inputs/outputs can be easily configured by adding or changing option cards. These option boards are designed to easy installation even on the site and are automatically identified by the inverter software.

SmartDrive PC connection tools and cables
Product description: SmartDrive 3.0m USB PC connection cable
HVAC400: yes
NXL HVAC: no
NXS: no
HVAC232/402: yes


SRC-10

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Room Connect; ErP Class VIII

For communication between Smile and HCE80, HR92, HCF82, T87RF. Integrated WiFi. Supplied with network cable.



SRR

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Mounting accessories for panel models

Reducing frame for panel cut-out on controllers ZG52 /53 /55 / 82 /85 or ZG215 /215V /252 /254



STB1

Centraline Safety limiting thermostat, with hand reset (STB1)

Sealing pipe thermostat with well.
Protection class: IP54
Housing material: Aluminium diecasting with plastic cover
Ambient temperature: 0...80C
Switch function/capacity: SPST 230 Vac, 10 A
Mechanical lock/reset: mechanical lock, with hand reset on outside of thermostat
Immersion depth: 150mm
Certificates: TUEV-approval STB895
Thermostat application: immersion tube thermostat
Thermostat functions: temp. setting inside, reset outside
Temp. setpoint range: 60...130C
Mounting place: in pipe
Immersion well material: red brass, nickel plated
Immersion well thread: R1/2"
Max. perm. temp. at sensor: 150C


STU25

Centraline Three-way rotary valve PN10
Accessories

Internal threaded socket with gaskets and cap nut, DN25, pipe size 25 mm



STU32

Centraline Three-way rotary valve PN10
Accessories

Internal threaded socket with gaskets and cap nut, DN32, pipe size 32 mm



SW2

Centraline Damper actuator 20/34 Nm, SmartAct
Optional accessories

End switch kit, with 2 SPDT freely adjustable end-switches



SWS-12

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Mounting accessories for panel models

Connecting base for wall installation



T4NST

Centraline Safety limiting thermostat, with hand reset (STB1)
Accessories

Steel well R1/2" x 150 mm



T7460A1001

Centraline Wall modules for EXCEL 5000 controllers

Room temperature sensor for Excel 10/12 and Excel 50..800 controllers. Models available with setpoint adjustment, occupancy extension and fan switch.
LED functions: LED on or blinking in case of bypass, LED functions programmable with Excel 20..800 controllers
Temperature element: NTC20k
Temperature range: 10...35C
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm
Models with setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.


Setpoint knob: no
Extra setp. knob: no
Occupancy switch: no
Fan switch: no


T7460B1009

Centraline Wall modules for EXCEL 5000 controllers

Room temperature sensor for Excel 10/12 and Excel 50..800 controllers. Models available with setpoint adjustment, occupancy extension and fan switch.
LED functions: LED on or blinking in case of bypass, LED functions programmable with Excel 20..800 controllers
Temperature element: NTC20k
Temperature range: 10...35C
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm
Models with setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.


Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: no
Fan switch: no


T7460C1007

Centraline Wall modules for EXCEL 5000 controllers

Room temperature sensor for Excel 10/12 and Excel 50..800 controllers. Models available with setpoint adjustment, occupancy extension and fan switch.
LED functions: LED on or blinking in case of bypass, LED functions programmable with Excel 20..800 controllers
Temperature element: NTC20k
Temperature range: 10...35C
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm
Models with setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.


Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Fan switch: no


T7460D1005

Centraline Wall modules for EXCEL 5000 controllers

Room temperature sensor for Excel 10/12 and Excel 50..800 controllers. Models available with setpoint adjustment, occupancy extension and fan switch.
LED functions: LED on or blinking in case of bypass, LED functions programmable with Excel 20..800 controllers
Temperature element: NTC20k
Temperature range: 10...35C
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm
Models with setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.


Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: no
Fan switch: auto/off/1/2/3


T7460E1002

Centraline Wall modules for EXCEL 5000 controllers

Room temperature sensor for Excel 10/12 and Excel 50..800 controllers. Models available with setpoint adjustment, occupancy extension and fan switch.
LED functions: LED on or blinking in case of bypass, LED functions programmable with Excel 20..800 controllers
Temperature element: NTC20k
Temperature range: 10...35C
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm
Models with setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.


Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Fan switch: auto/off/on


T7460F1000

Centraline Wall modules for EXCEL 5000 controllers

Room temperature sensor for Excel 10/12 and Excel 50..800 controllers. Models available with setpoint adjustment, occupancy extension and fan switch.
LED functions: LED on or blinking in case of bypass, LED functions programmable with Excel 20..800 controllers
Temperature element: NTC20k
Temperature range: 10...35C
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm
Models with setpoint potentiometer delivered with 4 setpoint wheels; white and blue, relative and absolute scale.


Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: auto/bypass
Fan switch: auto/off/1/2/3


T7460LONJACK

Centraline Wall modules for EXCEL 5000 controllers


LON connection board (5 pieces)



T750120

Centraline V5005T Kombi-FCU Pressure Independent Balancing and Control Valve
Accessories

Radiator Thermostat Thera-2080WL with remote sensor for water and air



T7560A1000

Centraline Wall modules for EXCEL 5000 controllers, with display

Room temperature sensor with digital display, for Excel 10 and Excel 50..800 controllers. With setpoint adjustment, occupancy extension, fan speed button and on/off button. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
centigrade/fahrenheit
Temperature element: NTC20k
Temperature range: 10...40C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: configurable
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


R.H. range: no
R.H. sensing element: no
R.H. output signal: no
Wiring terminals: 7
Model: blue knobs/wheel


T7560A1018

Centraline Wall modules for EXCEL 5000 controllers, with display

Room temperature sensor with digital display, for Excel 10 and Excel 50..800 controllers. With setpoint adjustment, occupancy extension, fan speed button and on/off button. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
centigrade/fahrenheit
Temperature element: NTC20k
Temperature range: 10...40C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: configurable
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


R.H. range: no
R.H. sensing element: no
R.H. output signal: no
Wiring terminals: 7
Model: white knobs/wheel/fahrenheit


T7560A1026

Centraline Wall modules for EXCEL 5000 controllers, with display

Room temperature sensor with digital display, for Excel 10 and Excel 50..800 controllers. With setpoint adjustment, occupancy extension, fan speed button and on/off button. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
centigrade/fahrenheit
Temperature element: NTC20k
Temperature range: 10...40C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: configurable
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


R.H. range: no
R.H. sensing element: no
R.H. output signal: no
Wiring terminals: 7
Model: white knobs/wheel


T7560B1008

Centraline Wall modules for EXCEL 5000 controllers, with display

Room temperature sensor with digital display, for Excel 10 and Excel 50..800 controllers. With setpoint adjustment, occupancy extension, fan speed button and on/off button. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
centigrade/fahrenheit
Temperature element: NTC20k
Temperature range: 10...40C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: configurable
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


R.H. range: 5...90%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Wiring terminals: 8
Model: blue knobs/wheel


T7560B1016

Centraline Wall modules for EXCEL 5000 controllers, with display

Room temperature sensor with digital display, for Excel 10 and Excel 50..800 controllers. With setpoint adjustment, occupancy extension, fan speed button and on/off button. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
centigrade/fahrenheit
Temperature element: NTC20k
Temperature range: 10...40C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: configurable
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


R.H. range: 5...90%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Wiring terminals: 8
Model: white knobs/wheel/fahrenheit


T7560B1024

Centraline Wall modules for EXCEL 5000 controllers, with display

Room temperature sensor with digital display, for Excel 10 and Excel 50..800 controllers. With setpoint adjustment, occupancy extension, fan speed button and on/off button. Model with R.H.-sensor.
Display functions: room temperature, setpoint temperature, occupancy status, fan speed status
Tool-free configuration:
number of fan speeds
relative / absolute setpoint
enable/disable space temperature display
centigrade/fahrenheit
Temperature element: NTC20k
Temperature range: 10...40C
Setpoint knob: -5...5C
Extra setp. knob: 12...30C
Occupancy switch: on/off
Fan switch: configurable
Power supply: 24Vac
Mounting place: internal wall
Housing (HxWxD): 104mm|99mm|30mm


R.H. range: 5...90%rh
R.H. sensing element: capacitive
R.H. output signal: 0..10V=
Wiring terminals: 8
Model: white knobs/wheel


T7560BLINDS

Centraline Wall modules for EXCEL 5000 controllers, with display
Accessories

Blind cover for T7560 knobs (50 pieces)



TBS-SMILE

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Mounting accessories for panel models

Terminal block set for Smile controller (N-version), 10 sets



TBS-smile-1kit

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Mounting accessories for panel models

Single Terminal block set for Smile controller (N-Version)



TG510A

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Tamper proof covers for setpoint units

Cover for SDW10..



TG511A

Centraline Heating, District Heating and Multi-Fuel OTC Controller, SMILE
Tamper proof covers for setpoint units

Cover for SDW30..



TPU-11-01

Centraline EAGLEHAWK Integrated Plant Control
Extra parts for EAGLEHAWK controller

Removable terminal plugs, push-in type; complete set of 3 plugs (for terminals 1 - 47); for the CLEA2000Bxx



TPU-45-01

Centraline EAGLEHAWK Integrated Plant Control
Extra parts for EAGLEHAWK controller

Removable terminal plugs, push-in type; complete set of 9 plugs (for terminals 1 - 47); for the CLEA2014Bxx and CLEA2026Bxx



V5004TF1050

Centraline V5004T Kombi-QM Pressure Independent Balancing and Control Valve

The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN250
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html

Rotary valve with actuator included, providing position feedback
DN size: 50mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 2000l/h
Maximum flow (qs): 20000l/h
Delta-P: 40...400kPa


V5004TF1065

Centraline V5004T Kombi-QM Pressure Independent Balancing and Control Valve

The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow systems. They may be used as constant flow limiter in constant flow systems (without an actuator) or as a Pressure Independent Control Valve in variable flow systems.
V5004T Kombi-QM is typically used for balancing and temperature control of fan coil units, air handling units, chilled ceilings and one-pipe heating systems.
Automatic pressure independent balancing and control
Precise pressure independent flow performance
Highest energy saving potential due to efficient energy transfer and minimized pump speed
Integrated measuring possibility to find the optimal setpoint for the pump
Reduced movements of actuators as pressure fluctuations do not influence the required temperature
No complex calculation needed for selection
No balancing method needed for commissioning
Wide range of application
Sizes DN15 up to DN250
Various versions to support standard flow rates as well as low flow and high flow needs
Covers two functions in one valve which reduces mounting costs
Easy commissioning
Pre-setting with visual flow scale at the valve
Pre-setting by hand without the need of tools
Pre-setting possible even when the system is running and an actuator is already mounted
Can balance a system even if only parts of a building are in operation
Maintenance friendly
Emergency shutoff function with plastic cap - not for permanent use
Measuring possibility for problematic applications
Medium type: water or water-glycol mixture according to VDI 2035
Media temp.: -10...120C
Max. delta P: 400kPa
Pre-setting: yes
Automatic balancing support: yes
Connection of accessories: side connections
Place in installation: return
Leakage: According to Class IV IEC 60534-2-3
Pressure Independent PICV
http://www.hydronic-balancing.info/home-en.html

Rotary valve with actuator included, providing position feedback
DN size: 65mm
Port connection: flanges
Port diameter: no
Minimum flow (qi): 3000l/h
Maximum flow (qs): 30000l/h
Delta-P: 30...400kPa


V5004TF1080

Centraline V5004T Kombi-QM Pressure Independent Balancing and Control Valve

The V5004T Kombi-QM is a Pressure Independent Control Valve (PICV). It combines a flow controller and a full stroke, full authority temperature controller in one valve. Equipped with an actuator Kombi-QM provides a full stroke modulating temperature control. It is suitable for use in variable and constant flow sy